Jump to content

Log in or register to remove this advert

Today's Posts

Showing status updates, topics, adverts, blog entries, articles, News, reviews, fungi, knots, records, images, albums, products, events and Freelancer posted in for the last 2 days.

This stream auto-updates

  1. Yesterday
  2. its down to the humidity.
  3. dumper

    Oh sod off

    I thought the felling cut on the sycamore looked good was it on rate my hinge?
  4. Stating the obvious the inlet needle is leaking, so either the metering lever is too high, or the metering diaphragm is too stiff, the rubber tipped needle is worn, orn the seat itself is worn, which is pretty normal on an old power cutter due the abrasive dust passing through the carb, when you changed the carb, was it a Chinese copy carb? at best they are not very good.
  5. A bit of both - always have toast and marmalade/jam for breakfast but give lots away to neighbours, friends and some of my favourite customers. Seems to be well received and get swaps with some veg, fruit etc Fig chutney goes down well at my local pub on cheese night. The Bramley apples are numerous this year if not as big as usual due to the lack of rain. Apple pies and crumble will be going in the freezer soon as well.
  6. AHPP

    Clutch spring hack

    I fycking hate the thing anyway. Heavy, loud bastard. Fcxk off. I want a 40 foot birch I can do with a zingy little 2511 and a packet of sweets.
  7. The Microbull grab with the hydraulic capstan on it still sounds like the bollocks to me. A shame they didn't catch on more. The controls are gash and the showroom is far less easy to get to than Chesterfield. Both surmountable problems. Someone must want a small machine on tracks.
  8. Basically it can't comply to the European Normative Standard that splices are tested in accordance with. It might be a different story in other parts of the world. I'm not saying it's unsafe to climb on, it's just difficult to prove that it IS safe. Reach out to the supplier and ask if their splicer has been trained by Courant.
  9. Nobody has been brave enough to ask!
  10. If you're local to me please don't being it in for repair. I've had a few machines in that have had used engine oil for chain oil. They either get picked up without me looking at them or get binned. The next down the line is veg oil machines!
  11. Give them a ring and they have some good relationships with people and they can quite often arrange for you to go and see one nearish you.
  12. sime42

    Jokes???

  13. I’ve used Ecoplugs on side growths and suckers, and they work well if applied correctly. Drilling at the right angle into the stem and ensuring the plug sits flush is key for effective herbicide delivery. They’re cleaner and more targeted than spray treatments, especially in sensitive areas where drift or overspray could be a problem.
  14. APF 2022, Pete Bags drinking red wine through a straw. Good times.
  15. Time Left: 6 days and 10 hours

    • FOR SALE
    • USED

    New shop soiled 13.5HP Briggs & Stratton petrol engine Comes with 14ft bed which will allow a milling length of 11ft Maximum log diameter of 27” and a board width of 22” Sold as seen Viewing available at Long Bennington

    Ask for price

    Long Bennington, Nottinghamshire - GB

  16. This item is SOLD

    • FOR SALE
    • NEW

    New shop soiled 13.5HP Briggs & Stratton petrol engine Comes with 14ft bed which will allow a milling length of 11ft Maximum log diameter of 27” and a board width of 22” Sold as seen Viewing available at Long Bennington

    Ask for price

    Long Bennington, Nottinghamshire - GB

  17. I used to plant lots of trees in Denmark but they never used to start things until early April which seems late by UK standards it's maybe because in the past they were used to long winters. Sometimes there would be stuff to do in November/ December but not as much
  18. Wordle 1,518 5/6 ⬜⬜⬜⬜🟨 ⬜🟩⬜⬜⬜ 🟩🟩⬜⬜⬜ 🟩🟩🟨⬜⬜ 🟩🟩🟩🟩🟩
  19. Good Morning All.
  20. Time Left: 6 days and 4 hours

    • WANTED
    • USED

    I'm looking for one or two of the above saws for snedding out in coppicing work. Ideally pick up distance from Kent or would need to be couried, thanks in advance The price offered is for a tidy example that runs well

    £140

    - GB

  21. Last week
  22. I was going to say I wonder how it will go with Putin tomorrow, but after reading the last few pages I think I will leave the pedo, sex trafficker sympathises to their own devices. Bye.
  23. Vat of Chilli to freeze up for the old folk! Teaching then how to read a packet mix! Sweet!
  24. Hi, I'm looking for self employed groundy/brush cutter operators to help out on some late Himalayan Balsam control sites, in wetland near Knutsford/ S.Manchester. Other dates are a possibility. Wellies and some prior experience are necessary, but no machines or cert needed, really. Call me for further details. Nick 07973 701 898
  25. Job Description We are looking for a self motivated HarvaDig drive to join our Forestry department who has a passion for working in the outdoors and in a forest environment. We work in many locations in and around Gloucestershire, Worcestershire, Herefordshire and beyond. The role of the HarvaDig driver would be harvesting timber ready for staking. The candidate must be confident at driving a digger and from a rural back ground with general knowledge of agriculture. FMO tickets would be a bonus but not necessary as these can be attained for the right person. Must be hardworking and work as part of a team. Must be able to work to deadlines. Bonus scheme. Possible overtime. Competitive salary depending on experience. 29 days holiday. Company car. PPE provided. Job Type: Full-time, permanent Pay: From £35,000.00 Ability to commute/relocate: - Cheltenham GL54 5HF: reliably commute or plan to relocate before starting work (required) Experience: - Agricultural: 1 year (preferred) - Digger driving: 2 years (required) Licence/Certification: - Driving licence (required) Work Location: In person
  1. Load more activity

About

Arbtalk.co.uk is a hub for the arboriculture industry in the UK.  
If you're just starting out and you need business, equipment, tech or training support you're in the right place.  If you've done it, made it, got a van load of oily t-shirts and have decided to give something back by sharing your knowledge or wisdom,  then you're welcome too.
If you would like to contribute to making this industry more effective and safe then welcome.
Just like a living tree, it'll always be a work in progress.
Please have a look around, sign up, share and contribute the best you have.

See you inside.

The Arbtalk Team

Follow us

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.