Today's Posts
Showing status updates, topics, adverts, blog entries, articles, News, reviews, fungi, knots, records, images, albums, products, events and Freelancer posted in for the last 2 days.
- Past hour
-
the Honda information sheet I linked to doesn't say about reseting the gaps when warm, it just says If adjustment is necessary, proceed as follows: a. Hold the rocker arm pivot and loosen the rocker arm pivot lock nut. b. Turn the rocker arm pivot to obtain the specified clearance. c. Retighten the rocker arm pivot lock nut while holding the rocker arm pivot. TORQUE: 10 N·m (1.0 kgf·m, 7 lbt·ft) d. Recheck valve clearance after tightening the rocker arm pivot lock nut. Not sure if this reseting on a warm engine is the right thing to do? Anyway, at least it's running.
-
Back to my 661, the reason I was doing clutch springs is that it's been running on very badly during some HEAVY use recently. Maintaining a really high idle until I slowed the chain on some wood and then blipped the throttle. Should I do the M tronic reset? The rev it for two minutes thing.
-
I assume these are pier bits? What's the eventual repurposed use?
- Today
-
Yes .,seems I WAS wrong 😀 Like you a assumed he had read it because he posted it . Assumptions , assumptions !
-
Todays pick.
-
Old Christmas tree that went a bit mental. Drop zone was main issue on this one, but nothing broken that shouldn't be😁
-
You need a pressure tester mate, this will tell you straight away if the needle and seat are leaking, you will never get it to run properly with a leak at the needle, just looking at will not tell you if it is leaking.
-
I tend to agree, whilst the US has picked up the slack and Trump gets slated the fact of the matter is the western NATO countries with the exception of a couple of members have gutted their armed forces to the point that they are virtually useless. The UK in particular has huge problems at the minute, whilst we have politicians grandstanding about “ the coalition of the willing” the reality is we couldn’t even begin to defend our own country never mind venture farther afield. We can’t even stop a few dinghies crossing the channel at the minute.
-
We have one used it twice the chain is far to aggressive for the size of the machine and the bar length if you don’t hold it tight with both hands it will rip it of your grasp,The stihl gt40 much better to use ,I am a big Milwaukee fan but not of this ,
-
All these cheap skid steer loaders about…….
Mark Bolam replied to Treetom15's topic in Large equipment
Same headstock as Avant. -
Hello, would anyone have a Lucas mill they'd be interested in selling? A 10-30 or an 8-30 would be perfect. Nooie
-
I looked at one of these online, they have a video of it running. It looks painstakingly slow. My CS100 is significantly quicker, but lacks the feed roller and anti stress. I did request a demo, living near Carlisle, nothing came of it though and ai didn't follow up. The GL&D looks a a far better small chipper, also double the price...
-
They are. They're at the yard but I'll get back to you on Monday about that.
-
Missed a few days, been in a field in Heacham. This is my 1000th wordle. Wordle 1,519 4/6* 🟨⬜🟨⬜⬜ 🟨⬜⬜🟩🟩 ⬜🟩⬜🟩🟩 🟩🟩🟩🟩🟩
-
Thanks to everyone for all your input- very much appreciated, and thank you to those that messaged privately, either to offer leads or contacts. Cheers!
-
Its a wind up , godda be !
-
I know, and they seemed surprised when I told I didn't want to go ahead. Funnily enough a friend took a still in and they did a great job by all accounts!!
- Yesterday
-
its down to the humidity.
-
Basically it can't comply to the European Normative Standard that splices are tested in accordance with. It might be a different story in other parts of the world. I'm not saying it's unsafe to climb on, it's just difficult to prove that it IS safe. Reach out to the supplier and ask if their splicer has been trained by Courant.
-
Jas P Botex & Mantis - Looking for suggestions
Brushcutter replied to TreeDB's topic in Large equipment
Give them a ring and they have some good relationships with people and they can quite often arrange for you to go and see one nearish you. -
Using Ecoplugs on side growths and suckers
wallyrobinett replied to Philadelphus's topic in General chat
I’ve used Ecoplugs on side growths and suckers, and they work well if applied correctly. Drilling at the right angle into the stem and ensuring the plug sits flush is key for effective herbicide delivery. They’re cleaner and more targeted than spray treatments, especially in sensitive areas where drift or overspray could be a problem. -
APF 2022, Pete Bags drinking red wine through a straw. Good times.
-
.thumb.jpeg.4c5efbb0b23507b74cfd8eb5351be9dc.jpeg)
Time Left: 5 days and 18 hours
- FOR SALE
- USED
New shop soiled 13.5HP Briggs & Stratton petrol engine Comes with 14ft bed which will allow a milling length of 11ft Maximum log diameter of 27” and a board width of 22” Sold as seen Viewing available at Long BenningtonAsk for price
Long Bennington, Nottinghamshire - GB
-
.thumb.jpeg.857dbb710f1f277635e9b21618c3ddef.jpeg)
This item is SOLD
- FOR SALE
- NEW
New shop soiled 13.5HP Briggs & Stratton petrol engine Comes with 14ft bed which will allow a milling length of 11ft Maximum log diameter of 27” and a board width of 22” Sold as seen Viewing available at Long BenningtonAsk for price
Long Bennington, Nottinghamshire - GB
.thumb.jpeg.4c5efbb0b23507b74cfd8eb5351be9dc.jpeg)
.thumb.jpeg.857dbb710f1f277635e9b21618c3ddef.jpeg)
