Today's Posts

I do much the same but you need to be aware that if the cord is two thin it can spool on side by side rathan than on top of the previous layer and when you pull it to start it wedges the plastic pulley apart.

Yes she has. I was watching an episode of KUA last night. Was very good, but every episode was the same. Had the writer developed the characters more and placed them in different situations, it could have been as good as Only Fools and Horses.

Yes Les, role in the Business Support bit of an Arb contractor. Partially on spanners and fleet care etc. Totally away from Sales etc. Good people who I've known for years and right looking forward to the changes!

Storm damage clearing. More to come

Easily done… I’ve got one on my Vermeer it’s very useful. You can get a avant headstock made up easily enough and with the extra weight it would be decent I’d wager. The winch is 3.5t and doubled up on a block it’s a powerful tool! I primarily used it for one job winching off felled timber on an incline. I’d probably sell on… feel free to dm.

I have a 2016 timber 230dhb. The feed rollers work fine in reverse. They will only work going forward if I hold the button down on the side, as soon as I release the button they stop. Could it be the solenoid? I have changed the stop bar button.

I did have a lie in Mark, but... Wordle 1,568 2/6 🟩🟩🟨⬜🟩 🟩🟩🟩🟩🟩 🖕

Roots are " pot bound " . Should have teased them out before planting .

Pigs will clear anything, but ground nesting birds won't survive. Fenced off just to the bracken areas could work. Electric fences.

Type of tree will help as some are more desirable than others and is there easy vehicle access, will it be down, machine for loading or rings to handball? Free or beer tokens?

No . They have a few tablets ( pardon the pun ) that the staff go through it with them . One woman said on the phone that she had no internet so could not do it . My missus said " you have an email address " well I don't use that the woman said the woman . It has saved , on average about 300 phone calls a day so far .

Ill adjust it to 1.5,yeah it is old , but like I say if you keep trigger on it runs and cuts etc fine,just wont idle for long

Approved.

Presumably a 500i has a map for different injection timing depending on revs, load etc too.

Strimmers, trees and the public. A dangerous mix.

Town and Country Planning Act 1990 WWW.LEGISLATION.GOV.UK An Act to consolidate certain enactments relating to town and country planning (excluding... Section 197 of the Act is the guiding legislation as to why Arb Impact Assessments are sought for in connection to planning applications regardless of conservation area status. The council's website should have a validation checklist, which should specify what type of report is needed for different planning applications.

How did you try to lift it? With a/the rope and pulley up the tree (can't see from video if you crotched it or used a pulley/ring/biner)? Or just by hand on the ground?

Milling finished so a quick update. The 18mm ply board with 45 degree blocks worked a treat. Fixed it to each quarter with a screw at each end and milled down to one board past the ‘centre’. Then removed the board, flipped the log over and finished milling the second half. In each quarter, the ray fleck figure is visible in the four centre boards as I’d hoped, so I’ve the option of jointing each set of four planks to make four 0.9m to 1.0m book matched ‘slabs’. Maybe table tops? Planks are generally very good, with a few small / pinhead knots. A few splits around the heart in some boards, but I’ll cut that off in due course. Overall, looks like grades 1A and 1B based on the pictures in the publication ‘Making the Grade’. Not bad for a 160 / 170 year old garden tree and thankfully no nails. Re the volume of useable timber, the log started as about 40 hft (hoppus measure). After milling there is an average 10 planks per quarter and a total from the four quarters of about 30 cu ft of planks including sap. Having measured the planks excluding bark, sap, heart and splits, the quartersawn heartwood volume is 20 cu ft with planks generally 200mm+ width with a max of 270mm width and up to 350mm at the flare at the bottom of the log. Interesting to see that the heartwood measure is half the hoppus measure, which I guess gives a better idea of the ‘value’ in a log? The upper log was milled slightly differently to the earlier sketch. I was looking for roughly 10 x 2 planks which will be trimmed to different widths after drying to exclude sap, etc. Just aiming to have some stock of oak, not for anything specific at the moment. There was a shake I’d forgotten about, we found a patch of rot from a broken branch and other issues, so we adjusted the cut pattern as we progressed to keep faults on the sides of planks rather than in their centre. Got 18 square edged planks with six quarter sawn / ray flecked planks, three either side of the heart, plus flat and rift sawn planks. All the planks from both logs now moved from the sawmill and about half stacked and sticked with 20 x 12mm sticks at 400mm centres. Waiting for storm Amy to pass in the meantime and after finishing the stacking, will cut and split all the offcuts for our stove. Nothing wasted! Overall, milling these two logs has yielded some good timber for my ‘a hobby woodworkers’ future use. And lots of fun! Andrew

Could be a place to visit one day.

I get the use of the 760 regularly and have had the use of at least three other models over the last 5 years. Zero issues so far. I love them.

sorry Stubby, you were closer before.

NBC in 2011, Trump said: "In my opinion I hear the Democrats are going to be blamed and the Republicans are going to be blamed. I actually think the President would be blamed. If there is a shutdown I think it would be a tremendously negative mark on the president of the United States. He's the one who has to get people together."

wow - it's your lucky day - some guys have written a whole 50 page booklet 'weed control in Christmas tree plantations'. Merry Christmas https://cdn.forestresearch.gov.uk/2022/04/fcfb015.pdf