Milling Forum

2,969 topics in this forum

1. donaris bandsawmill

   By firewood, October 14, 2010
   • 2 replies
   • 2k views
   • 
   • firewood
   • October 23, 2010

2. Log in or register to remove this advert

3. Steaming question for kiln dryers...? 1 2

   By Big J, October 16, 2010
   • 10 replies
   • 3.1k views
   • 
   • Big J
   • October 22, 2010

4. Selling planks?? 1 2 3

   By Ian Flatters, September 3, 2010
   • 27 replies
   • 5.8k views
   • 
   • testcricket01
   • October 21, 2010

5. Lucas or petterson mill needed, gloucestershire

   By Theocus, October 6, 2010
   • 2 replies
   • 1.6k views
   • 
   • Rob D
   • October 7, 2010

6. electric chainsaw mills

   By ecolojim, October 3, 2010
   • 0 replies
   • 1.5k views
   • 
   • ecolojim
   • October 3, 2010

7. Mahogany + Chainsaw mill = good or bad idea?

   By kev_s, September 26, 2010
   • 8 replies
   • 2.5k views
   • 
   • WADKIN
   • September 28, 2010

8. Rob thanks for the Minimill, but......

   By openboater, September 25, 2010
   • 3 replies
   • 1.6k views
   • 
   • openboater
   • September 27, 2010

9. oak to mill 1 2

   By delabodge, September 21, 2010
   • 12 replies
   • 2.8k views
   • 
   • delabodge
   • September 25, 2010

10. Cedar to mill

    By openboater, September 23, 2010
    • 9 replies
    • 1.7k views
    • 
    • openboater
    • September 23, 2010

11. milled walnut trunk 1 2 3 4

    By Ben Ballard, September 18, 2010
    • 37 replies
    • 7.2k views
    • 
    • WADKIN
    • September 22, 2010

12. Jarvi Bench 1 2

    By Rich Rule, September 19, 2010
    • 11 replies
    • 3.2k views
    • 
    • delabodge
    • September 20, 2010

13. Hiring in a mill?

    By woodworm, September 19, 2010
    • 9 replies
    • 2k views
    • 
    • woodworm
    • September 19, 2010

14. from fallen trees wonderful shapes will grow again

    By robert t, September 14, 2010
    • 6 replies
    • 1.7k views
    • 
    • Cracker
    • September 19, 2010

15. My website is finally up

    By Big J, September 17, 2010
    • 7 replies
    • 2.1k views
    • 
    • Mike Hill
    • September 18, 2010

16. New Milling forum now open

    By Steve Bullman, September 14, 2010
    • 4 replies
    • 1.8k views
    • 
    • delabodge
    • September 14, 2010

17. to mill or not to mill? 1 2

    By plippy, February 14, 2010
    • 19 replies
    • 4.3k views
    • 
    • delabodge
    • September 14, 2010

18. Pricing for timber for milling 1 2 3

    By Big J, June 8, 2010
    • 22 replies
    • 6.8k views
    • 
    • Big J
    • September 11, 2010

19. Any ideas for milling hardwoods?

    By Rob Stringer, August 21, 2010
    • 5 replies
    • 2k views
    • 
    • tommer9
    • August 22, 2010

20. Books on how to make stuff???

    By Ian Flatters, February 11, 2010
    • 2 replies
    • 2.1k views
    • 
    • Rob D
    • February 18, 2010