spudulike

Then phone them, they will get in what you need if it isn't listed on the site but is available from Stihl!

Good subject this and congratulate you on sorting it out and hope your ethic flows down to your kids through their lives. 20 years is a good long time to save money over and compound growth is your friend. Compound growth is where you re-invest your earnings through dividends, interest or whatever and it increases the pot so has a much stronger impact than taking an income. I would stick the £4K in an equity ISA as they are a great way of tax free saving, the money going in may be taxed but when you have a good large pot, you can take money out with no tax implications. A decent ISA should be able to double its value every 7 years so in 21 years you should be able to double your £4k and double that then double that in the 21years period. There are no guarantees to this as equity can go up or down but long term, it makes a lot of sense. You may like to start in relatively safe European and UK funds but as they get bigger, look at China, Japan, Tech and North American funds. ISAs or its forerunner PEPs were predominantly UK based funds but that has now expanded. One caveat to this is that equity has had a long bull run so you could wait a bit and invest if you see a major decline in share price but.....you have to be in it to see the growth over time! Personally I would avoid any funds managed by banks etc. Do your research, select a fund and invest through a platform such as Interactive Investor as they charge very low administration fees but they will NOT advise you. My late father did exactly this for my nieces and £1000 grew to £6k in under 18 years....work it out!!!

Yup, looks like it...it has a torch light when you turn it on, it beeps when its near metal and faster when closer plus it vibrates as well Found this on eBay.....it will be a Chinese seller but with you in a week..... Metal Detector GP-POINTER Pin Pointer Water-Resistant HandHeld Gold Pinpointer WWW.EBAY.CO.UK 1 PC × Detector. Size: Approx. 215.5 41.5 43.52mm. Working Environm ent: Temperature -20 ℃ -60 ℃. 1 PC × User Manual. 1 PC × Leather Case. 1 PC × Pinhole. The sensitivity distance...

Sorry, missed your post. It is branded "GP Pointer". It looks like the Garrett pointer which is much counterfeited so watch out for fake ones if you see a bargain one. I have used it a fair bit over the last few years and helps direct you where to dig once you have a bit of a hole and can't tell exactly where the metal is.

They don't hold as much charge, short burst of energy and they are depleted unlike a battery/cell.

The CS4PI is a beach detector. PI detectors don't get effected by the mineral changes from dry to wet sand as many other detectors do. They have very deep detection, are a bit weird when you first try them if you are used to other machines but they go very deep but no discrimination like VLF based machines that can. On those "magic carrot" hand held pinpointers, they are useful when on the beach and the Chinese copies are actually quite good for the money!

Something like this - just tap the hole first and use a little permanent stud lock on it...... STAINLESS STEEL SLOTTED SELF TAPPING THREADED INSERTS NUTS M2.5 M3 M4 M5 M6 M8 WWW.EBAY.CO.UK M8 x 15 – 10.6 – 10.8. M4 x 8 – 5.8 – 5.9. · M2 x 6 – 3.8 – 3.9. M4 x 8 – Int – 0.70 Ext – 0.75. M2.5 x 6 – 4.1 – 4.2. M8 x 15 – Int – 1.25 Ext – 1.50. M6 x 14 – 8.6 – 8.8. M2 x 6 – Int...

With oiling issues I normally make sure the oil pimp isn't plugged with fine wood chip, make sure the pinion oil gear isn't shredded, check the oil pickup pipe (if fitted) isn't blocked and flush the oil tank. If the oil is getting to the pump, the pump is pumping and the oil pinion is turning the pump, you usually have oil flow. I think this is the IPL for your saw: - https://www.efcopower.com/sites/default/files/951_IPL.pdf I would assume that "sump plug" is a pre filter for the oil pump and probably draws the oil through that filter.

Good method, often works well.

Not sure what a "40" is like but the only one I have done had a worn oil pump and the whole engine had to come out to get to it. very poor design from this perspective. Never again, just not worth the time and effort! As Mark said............ball ache!

Where did you get that from....that is one of my bits of advice. Glad it sorted it BTW.

Yes but mine aren't the blind version.

....and shoot them

2.4KW = 3.2HP

I use marine stainless inserts as long as the land around the hole can support the size of the insert.

Give us a picture of the parts to be fitted and the bit they should fit to as it will help....lots!!

No, must have had four like it in the last month.....I think it is more obvious when you know to look. I run a bead of braze up the crack....will see how that works out.

Beginning to see a lot of these now, basically the heat from the MS201TC&M exhaust port keeps expanding and contracting the metal under the port until the metal cracks like this: -

The IPL shows four M5X18mm screws - looks like some amateur has been at it....not uncommon on an old saw!

No idea on the tank housing, have you pushed the AV annular buffers in fully? On the screw holes - I would look at the holes they are going in to and measure the depth if blind holes and fit the screws that won't bottom out. You have to make sure that the screws won't bottom out or puncture the material behind the screw which can lead to issues or damage to the saw. It is possible a numb nuts has fitted the incorrect screws. Some saws have a cylinder base of different thicknesses front to rear - like the 395XP and the longer ones go to the rear as the cylinder base is thicker to the rear of the cylinder.

From the IPL, it doesn't look like there should be a buffer there - http://thebakeliteradio.com/sawspares.com/Stihl 028AV IPL.pdf

I have Rays autobiography in a stack of books to read over the next year or two. Seems like a very interesting bloke and sure it will be an interesting read.

Thats what I call foreceps....mine were fishing ones for disgorging hooks.....and lock...and look the same as yours

Oil your tube end and the hole then push it in to the hole and pull it through with well worn non sharp pliers.....don't want to split the thing! You can use forceps on the other end if it isn't connected - good enough for arteries, good enough for fuel/impulse lines!

I think we should have a "Donate" charity button so people who get good advice and save themselves a bit of £££ can donate to an Arbtalk charity. What you say Mr Bullman?