Dan Maynard
-
Posts
4,849 -
Joined
-
Last visited
-
Days Won
4
Content Type
Profiles
Forums
Classifieds
Tip Site Directory
Blogs
Articles
News
Arborist Reviews
Arbtalk Knot Guide
Gallery
Store
Freelancers directory
Everything posted by Dan Maynard
-
Likewise M500 solid bit of kit, bigger engine at 24hp is one reason I went for one.
-
Well, not really a chair, nice textbook fell using Danish pie and wedge but main fork was weak with included bark so it split with a big bang when it hit the ground. No, I was not near it, yes I did jump a bit.
-
I would definitely be interested in a piston if the price isn't silly. It's been a good saw, although to be honest I use it less now I've got a 461. Taken down a few trees with it though, thought a pic would be nice.
-
Where did you find a 6800 cylinder? I thought they were all used up? I have a Dolmar 6000i which I bought from shavey, could ideally do with a piston but if I could get a bigger cylinder I'd put it on...
-
I think RobD on chainsawbars has some offers on the making and breaking tools at the moment, worth checking out if it would apply to you. That would be Oregon chain though.
-
I've seen pneumatic jockey wheels on boat trailers in the past so you can definitely get them, not bought one to be able to recommend something specific though.
-
I designed our fireplace, seem to remember the regs focus on distance to combustible materials and doesn't sound like yours are.
-
Maybe hydraulic rather than PTO?
-
Work have a 150 and a 230. No snedding with the 230, massively better at dragging in and crushing forks.
-
I've got a 2010 year 261 and never had a problem with needle bearings, I think it's a good saw. I was advised years ago to take off the spline/rim drive and fit a spur type clutch drum because of the bearings, obviously difficult to say if it would have been ok if I hadn't.
-
One of the T-piece photos on ebay has a laser engraved mark of PA6 on it, this is the material code which is nylon-6. According to Direct Plastics the nylon has a long term operating temperature range up to 100C whereas PVC only 60C - I would be nervous about using PVC on a heater outlet. https://www.directplastics.co.uk/data-sheets Not sure where that leaves you though, seems it's possible to get nylon pipe but difficult/expensive - maybe steel exhaust pipe is the best option as spuddog says - you could get the T cut and welded up and also weld any brackets or fixings you need on to it?
-
I used Stanley Jetcut to build green oak fence, panel saw was fine on 3" posts and rails but obviously going to be hard work on sleepers. The teeth are tri ground like a Silky but cut when you push.
-
Chap at work has the larger saw (different name can't remember) which also has coarser pitch, he also says he would rather it was a bit finer for smoother cuts when pruning. My Zubat is 7.5 which I would stick with for a replacement especially given what you have said.
-
You haven't listed spark plug but you must have changed it?
-
Coletti beat me to it. I thought about it because I hired a Timberwolf 13/75 once where the anvil gap was about 8mm, terrible on anything small as it all just got dragged through instead of cut and then of course that would clog it up. I also just wonder if there's something on the engine like air filter blocked, throttle cable set wrong, governor spring or whatever meaning you are not getting full rpm? That definitely will cause poor chipping, blocking, etc.
-
I have one, mine is on its second engine but some of it may be just as old as your hire one. It throws chip well, leaves less so. I have a 12 foot trailer and if I park it at the back the chip will easily reach the front, although some leaves will fall down in the gap so I usually tarp. It doesn't block often although you can block it, big lumps of Leylandii will do it if you let go the whole thing in one but just need to hold back part of it for a second or two. I sort of watch and judge how it gets on to gauge whether to slow it, most bits can just be thrown in. I do have quick release clamps on the chute though which is apparently a JB option, so blockage isn't a major trauma (no spanner, v quick to pop off and poke out). If it's a hire machine you've got though, question would be is it sharp and is the anvil gap correct? I'm assuming though that you are familiar with effect of sharpness from your CS100.
-
Judging from the number of adverts that don't get much response on here the constraint might well be staff rather than work for them to do.
-
I think she's saying 'All right boys, well done for cutting it down. Now cut me a log off the end.'
-
Just to pick up on the earlier point about previous conflicts and whether they were hard as nails, my wife's great grandfather died in 1920 from alcohol poisoning, her great uncle went up the fields in 1919 and shot himself. Nobody called it PTSD but they were never right when they came back from the trenches. I am not ex forces so no direct experience but I do think as a country we have a responsibility to our veterans, whether it's best done by the MoD or NHS or charity or someone else I'm not sure.
-
Yes, in the same situation doing trees part time I paid the insurance, did more tree work, and pushed my pricing up a little bit on private jobs to help cover it. As others have said, without it you're definitely not properly insured when someone else is helping you even if they are volunteering or have their own insurance. My conclusion, it's another one of the things which fill the gap between what people think tree surgeons make (because they charge a lot) and what they actually make.
- 13 replies
-
- 1
-
-
- public liability
- hse
- (and 2 more)
-
Buy the Dolmar version, it's orange.
-
Work on a footpath - Signage, pedestrian management etc.
Dan Maynard replied to William Clifford's topic in General chat
Looks like a pretty steady stream of cars, not somewhere I'd be looking to take chances. My thought would be that the hedge needs reshaping (eg clear right around barrier) so it can be managed with a flail in future, needing TM every year will be bonkers. -
The 271 291 391 series are the non-pro so comparatively heavy and slow. If you think Stihl you should look rather at 261 or 362, depending on what bar and what weight you are happy with.
-
Never ever heard of a shelf life on it, likewise lube oil - only petrol which has volatile parts that evaporate.
-
My dad always used to keep the chainsaw bar wrapped in a pair of jeans instead of plastic bar cover.
