-
Posts
14,767 -
Joined
-
Last visited
-
Days Won
8
Content Type
Profiles
Forums
Classifieds
Tip Site Directory
Blogs
Articles
News
Arborist Reviews
Arbtalk Knot Guide
Gallery
Store
Calendar
Freelancers directory
Everything posted by spudulike
-
Ms 150 shaking starts well but judders at the tip.
spudulike replied to Thompson Dagnall's topic in Chainsaws
The coils are limited and you can't really call that cutting as the saw must be damn near max revs! -
Ms 150 shaking starts well but judders at the tip.
spudulike replied to Thompson Dagnall's topic in Chainsaws
Almost impossible to see what you are talking about and not helped by using a saw at full tilt to do extremely light cuts but understand why seeing some of your work......nice BTW. Is the chain too tight? I usually get a screwdriver behind a cutter and spin the chain, it should NOT stop dead but spin on for an inch or two. I go back to the engine mounts - if you take the clutch off and take the inner cover off, there are two large head T27 screws behind it, both are engine mounts and should be tight! This is a common fault with the top handle saw, not seen a rear handle one yet. Saws do four-stroke when revved flat out but is difficult to detect on these small saws, may be worth checking the air filter is clean - solvent and compressor and also open the H screw out fully to the stop. -
Not being funny but if the pump is dispensing oil to the oil channel and it isn't making it to the chain, the oiler hole in the bar is either blocked or the hole doesn't line up with the oil channel - wrong bar. Have you tried using the bar the other way up.....after clearing the oil hole in the bar. I can't understand how the nuts are loosening if they are done up tight with a socket and tommy bar. I wouldn't even expect heavy vibration to cause it unless they haven't been done up very tightly.
-
Husqvarna 435 cylinder/ piston fault or something else?
spudulike replied to DaveyCrockett's topic in Chainsaws
Sounds like the carb is OK then. Was the gauze strainer checked? Both flywheels and coils can't be faulty - very strange one, difficult to pin it down without inspection.- 38 replies
-
- husqvarna 435
- non runner
- (and 3 more)
-
Ms 150 shaking starts well but judders at the tip.
spudulike replied to Thompson Dagnall's topic in Chainsaws
You are talking AV mounts, I am talking ENGINE mounts - the screws that hold the engine to the plastic cradle. If the stop switch is working, they are probably OK. -
Ms 150 shaking starts well but judders at the tip.
spudulike replied to Thompson Dagnall's topic in Chainsaws
Does the stop switch work? -
Husqvarna 435 cylinder/ piston fault or something else?
spudulike replied to DaveyCrockett's topic in Chainsaws
OK, sounds like is getting fuel then........ possibly the needle valve in the carb is stuck open. Does the saw still fire, has it fired with this flywheel and carb setup? These sorts of issues are difficult to sort and often, you just eliminate parts being faulty and the only part left is the route cause.- 38 replies
-
- husqvarna 435
- non runner
- (and 3 more)
-
Ah...80s Britain, do you find they work better with a bit of Rick Astley going in the background😉 Glad to see my dating was bang on!
-
Husqvarna 435 cylinder/ piston fault or something else?
spudulike replied to DaveyCrockett's topic in Chainsaws
Those marks on the piston and bore are very strange. Is the ring location pin still in place on the inlet side? I don't think they will effect compression as they look to be below the exhaust port roof but are strange, not something I have seen before. The fact the plug cap to ground is measuring continuity is probably enough to show the HT lead is OK. ADW mentioned the match between coil and flywheel, on some saws, there are a number of flywheels and coils available. If you don't use the correct combination, the plug can spark at the wrong time and the saw will never start. He will know the correct combination and if your part numbers are OK. It looks like the top end is OK, ring end gap is fine, this leaves fuel and ignition. Issues tend to be fuel related but some saws can have inherent weak coils. Was the plug getting wet with fuel when you were pulling it over? Did you try a bit of WD40/carb cleaner/GT85 down the carb to see if it would fire. When the carb was stripped, was there a decent amount of fuel in the pump AND metering side of the carb?- 38 replies
-
- husqvarna 435
- non runner
- (and 3 more)
-
Ms 150 shaking starts well but judders at the tip.
spudulike replied to Thompson Dagnall's topic in Chainsaws
Possibly a bar nose issue. These 150s do get front top and bottom engine mount issues and you can usually tell from the stop switch failing to switch the saw off! -
Feck me...lift lid and throw them in.....they can't be factory tools....they remind me of my days in 1980s production! I reckon you are a Husqvarna tool collector......have you got one of their Mincers?....I found one once at an antique fair, I wish I had purchased it! Nice oil pump tester😉
-
Husqvarna 435 cylinder/ piston fault or something else?
spudulike replied to DaveyCrockett's topic in Chainsaws
I recently did an MS200t that would spark across a 7mm gap with a good spark, it had a slight break in the HT line and under compression wouldn't fire at all. A new HT lead sorted it. 120psi is poor, very poor. I would expect at least 150psi with 170psi being good. This measurement is a bit subjective as different gauge types give different readings. The first pull can tell you a lot about the real state of the engine. If it doesn't make 70psi + after an energetic first pull then something is amiss! ADW has a reasonable😉 experience of Husqvarnas so it is worth taking note of what he said about the match of flywheel to coils and coils giving issues!- 38 replies
-
- 1
-
- husqvarna 435
- non runner
- (and 3 more)
-
With the Husky, you can reset it to default with the CST software but you must run it full tilt for a few mins to reset the AT unit to what the engine needs. Don't get hung up on the reset as it is a bit like resetting your car radio to factory - you then have to reset the bass and treble up to max and mess with the balance.....saws are the same, factory default is just a known starting point where the saw will run. You could try putting some Aspen or Motomix through it. These fuels degrease my bench well when it spills so would imagine it may well purge any old oil from the carb. It is possible the oil has hindered the needle valve or the fuel pump, hopefully it will clear in time. You can sort of understand someone doing it on a small top handle when the tanks are close together but on a fuel tank on a ground saw.....what a d!(K.
-
High BTUs on the Euc, it has a lot of resin and good heat!
-
I think there are a lot of families thinking the same!
-
Probably Corona and it's effect on the supply chain. Parts have been slower over the last month or so. Not made turn around times easy this year but most goes out in two weeks or under and local stuff can be as soon as 24-48 hrs if in for a general repair not needing too many parts!
-
Currently booked up until sometime near the end of Jan so just adding each customer to the growing list and telling them when to send kit in at the moment!
-
Nope, would be interesting to run one of mine against it. Circa 3 seconds difference in cut speed so circa 15% between the two!
-
Who was the seller? I know a few and can vouch for them! Looks fine to me!
-
I was just going to say the same thing. I ordered a few Echo parts and didn't mention who I was, I had a little issue so phoned and after a long chat about all aspects of saws, he sorted it all out with no problems at all. He is "Rob D" on this forum but best have a chat - prices online can be a starting point for some sites as once they are through the floor, there is no way back up.
-
I also meant to say that the marks look negligible and not worth worrying about. It is highly possible the hylomar caused the mark on the intake side and the mark on the exhaust side is where the piston has pushed against the exhaust port. It is also possible that the ports may have been slightly rough and have marked the piston but these cylinders are generally well made and will pull 180-200psi when fitted new and OEM. I will PM you on the squish!
-
Sorry, missed this one. I would say a bit of chip or dust has got down the inlet side forcing the exhaust side of the piston in to the wall thus marking it and the mark on the inlet side is the witness to the dust/chip that got in. Check the air filter is clean and also the rest of the air-box.
-
Thanks for letting us know, glad it worked out and I can stick another notch on the bench! Those springs are a bit interesting to fit, never found an easier way than the method I described.
-
I would just read through my "Whats on your Bench" thread and it will give you a good idea of how I diagnose issues. I have changed some of the way I work over the years plus have gained more experience though......nothing stands still!
-
Probably a bit of copper or butane formed from heating it.......beginning to feel a lot like Christmas😂