Rob D
-
Posts
6,085 -
Joined
-
Last visited
-
Days Won
3
Content Type
Profiles
Forums
Classifieds
Tip Site Directory
Blogs
Articles
News
Arborist Reviews
Arbtalk Knot Guide
Gallery
Store
Freelancers directory
Everything posted by Rob D
-
Thanks for taking the time to answer Alec. It looks a good product and would certainly compliment the Alaskan well.
-
I only get 2 of the cubic meter bags on my tipper. But if you just had a flat bed you could have it designed to take 4 cubic meter bags.
-
Can do for £775-00 inc vat and delivery. For Stihl Bar with sprocket nose, 2x granberg chains, 2x stihl, oiler and 56" alaskan with bracing kit.
Cheers, Rob
-
Lots of people milling wood on here so finding timber should not be a problem
-
Welcome to the forum.
-
Don't worry it's getting there and I may be getting the Mark II in July.... I think it's a great wendy house. There would be a demand but the trouble is - as always - is finding the buyers
-
Thought it was very good Josh. Nice and controlled, not rushing and liked the way you could get back out the way for the pieces to be lifted off (all but one piece anyway). Great work though and also good quality footage.
-
Ho ho! That was either well judged or well lucky!
-
Ditto above.... at 0.50 that was not too well thought out as it could have got caught up sooner, snapped the hinge then sprung back. But other than that looked ok. I thought the lowering line was pretty good as it pulled the bits away from the wood back towards the chipper.
-
Managed to find a vid on youtube on the ripsaw. Would go well with the Alaskan mills etc as you could break a log down into big posts then use this to cut your boards. Do you know if it's CE marked? How long have you had yours and how much have you used it?
-
Sounds good but I've got my boots really overflowing with new projects at the moment...
-
Thanks for the replies Alec. It's one of those hard things - what is harder to mill? Some softwoods full of sap are quite fibrous and sticky and so perhaps are harder to mill.... What's the smaller bandsaw you have going there?
-
As far as milling width you'll only get a max cut of 16" with the small log mill using your MS361 + 18" bar. you could increase this to 18" using a 20" bar. You will only get a 12" width cut using an Alaskan (because it clamps on in 2 places on the bar) and you can't just use one clamp as it does not pinch the bar securely like the small log mill does. With 18" bar you'll be pretty accurate with the small log mill. Smoothness of cut comes down to using ripping chain and good chain sharpening. May be a tad thicker (1/8") on the far end if you went to a 20" bar with the MS361....
-
I don't know Tom. I've seen a lot of the small bandsaws at shows and I have a to say although wasteful I find the chainsaw mills are more accurate. The smaller bandsaw mills will cut softwood alright but you put some oak with a knot or two on and they do seem to waver in the cut.
-
Course you're welcome and ask away! One pointer. If you have questions about PPE and chainsaw use in general the first thing you will have fired back at you is have you done the relevant CS qualifications. If you are planning on using a chainsaw in your woodland you need a) the correct equipment and b) the correct training. This is your first port of call.
-
Yep this has limited swing potential - you have about 3" of play! But it does also go sideways! Having trouble trying to find those big springs they use on swing seats.... any ideas?
-
You know about these other sites then Tony :001_tt2:
-
Hope so. I'm trying to develop what things actually sell. So far way out in front are coffee tables about 4 foot long, 14" ish wide with 3 rustic legs. People can fit them in their boot and drive off. I've made loads of big dining tables but they're harder to sell as unless made to order people have a specific idea of what they want. But more or less everyone has a need/space for a swing seat! Next one will have a frame made out of branches pinned with those long threaded bits of steel.
-
Also just seen the solid wood locks! Brilliant!
-
That's even better finished. Like the holes on the left... they somehow really suit it. Do they have a purpose or just aesthetic?
-
I'd mill it with your chainsaw mill as thick as possible then take it to a bandsaw. You'll lose a bit in kerf but would save getting a mill in. Post some pics up when it is milled!
-
Looks goods. May see if the missus will be up for it this weekend. Thanks for the tip.
-
Have you not got a mill to break it down with? Sounds like a lovely bit of wood!
-
Doesn't look bad at all. Is there height graduations so you know what thickness you're milling to?
-
I've done that before... It's so easy to get complacent and not back up and heart breaking when this happens.... there'll be more (and better) pics out there and now you'll be even more keen to get 'em!
