Today's Posts

You need to check if its damaged. Its a bit of a complicated setup but IIRC you need to follow the wiring from the motor back to where it goes into the tube. From the tube it curls around the articled part and its the bit after that where the issue is.

The AI Machine Men Snatching Our Souls WWW.DONOTPANIC.NEWS (**************** AI Part II)

Never heard of them, but sub 12 I'd stick to air arms pellets as they're available practically anywhere and were always consistent and cheap. Most pellets are made in just 2-3 factories, H&N were making Bisley and a few others brands when you peeled the barcode label off the back.

Probably did! £20 labour soon disappears once you take the machine in, tag it up write out the quote and phone the customer, usually several times, never mind repairing the thing. Hopefully it will help someone in the future if they come accross the same issue and this thread.

Yes, it certainly thrives, but on the flip side, this is going well where the mint died off (mint also has that reputation). Yes, great fresh, over to the cooking thread - I tend to sort of follow the BBC recipe, horseradish, vinegar, double cream, mustard.. and some garlic just because... It is only me that goes for it so really just make it Christmas time when we have loads of spare cream around (To be fair, it also works with whipping cream and single cream depends what is open)

Bubba!

Can't go far wrong looking to the sailing industry for wet weather gear. Musto's one of my favourite brands, but pretty expensive. My lads had one of these for the past 12 months now and rates it....half price at the moment musto.com WWW.MUSTO.COM

Talking rats ! Whatever next 🙂

Sort of but what's that got to do with the price of fish?

A fairly recent auction of JCB odds and sods from the factory also unusually had quite a few lots that had come from a harbour somewhere 🤔 JCB are committed to the Hydrogen economy so it would not be that surprising if they had identified Milford Haven as the ideal place to berth ammonia tankers from sunnier climes.

Of course... You're british,right?! 😁 Around here in Romania we have electric 2 wheel "things" going 90km/h on Highways... And it's worse the more East you "dare" to go... Basarabia/Moldova, Ukraine, God forbid you step into Russia... Anything is possible in Russia... Aliens are afraid to visit Russia... Anyway...

Lucky it didn't get propelled up the chute. A good reason not to stand in front of it and to keep the truck rear window protected.

What have you got?

Thank you all for your kind replies. Appreciate it! Photo attached. No TPO.

Too many choices today. Wordle 1,611 5/6* ⬜⬜⬜🟨⬜ ⬜🟩⬜⬜🟨 ⬜🟩🟩🟩🟩 ⬜🟩🟩🟩🟩 🟩🟩🟩🟩🟩

Sorry, this is a British forum (.co.uk); people here won't try to advise you. All we can recommend is finding locally appropriate advice. Good luck.

IMG_6112.mov Sailor just being a fine figure of a dog on the penultimate drive today. Tied up because he’d just tested my patience on some bloke’s labrador and I needed to drop a length of fencing during this one anyway. His best work went unrecorded because I was too busy laughing a rib out. Big field of waist-high dead peas. Woodcock up straight away. Then zigzagging like he knows what to do, three or four pheasants. I praise him and riding high on the adrenaline and my satisfaction he bounces across the field like a blesbok, springing three feet straight up and down, not in slow motion but as if the world just stopped for a moment to marvel at it. Magnificent. Pissed myself to the point I couldn’t blow the whistle.

Can you give an idea of the day rate please?

If you block the fuel inlet to the carb, just put your thumb over it and create a vacuum on the primer side, put some fuel pipe on it and suck you should not be able to draw air through, if you can you either have a hole in the pump gasket or usually a bad check valve.

Hi, We are looking to hire a tree surgery assistant groundsman. Based in oxfordshire we also cover buckinghamshire, reading, milton keynes, greater london and london . Must have qualifications and experience as well as drivers license. feel free to get in touch via Whatsapp on 07831 693280

You could start an eBay shop.

It's taken a while - we now have 1/4 drive sprockets for the 540XPs. These are exclusive to us. No one else has them in the world (as we developed the mold for them). What this means is you can run 1/4 .043[1.1mm] chains on your 540XP. AND you could also run carving bars - the sprocket will run both 1/4 .043[1.1mm] and 1/4[1.3mm]. Find the sprocket here: 5774897-08Q Spur Sprocket 1/4 x8 tooth [Husqvarna T540XP, 540XP Mk I, II, III] WWW.CHAINSAWBARS.CO.UK 5774897-08Q Spur Sprocket 1/4 x8 tooth [Husqvarna T540XP, 540XP Mk I, II, III]. Allows you to run Dime tip carving bars and... Find the sprocket removal tool here: 4507 [502 54 16-03] Husqvarna Sprocket Clutch Removal Tool WWW.CHAINSAWBARS.CO.UK 4507 [502 54 16-03] Husqvarna Sprocket Clutch Removal Tool [42, 242, 340, 345, 346, 350, 351, 353, 455, 460, T540 XPs]... Bars - go for one of these here: Tsumura 1/4 .043 Black Edition - Chainsawbars WWW.CHAINSAWBARS.CO.UK And watch the video here please - shows fitting and other info:

Turns out it is the X having checked, so must be the same as all others. Cheers