Today's Posts

🤷‍♂️😂😂😂

Wessex,Fleming- depends what's around in your area look on marketplace to see ,horsey lot sell them off cheap enough, not much goes wrong on them

No2DigitalID — Big Brother Watch BIGBROTHERWATCH.ORG.UK https://bigbrotherwatch.org.uk/wp-content/uploads/2025/09/Checkpoint-Britain.pdf Petition: Do not introduce Digital ID cards PETITION.PARLIAMENT.UK We demand that the UK Government immediately commits to not introducing a digital ID cards. There are reports that this is being looked at. New digital ID scheme to be rolled out across UK - GOV.UK WWW.GOV.UK A new digital ID scheme will help combat illegal working while making it easier for the vast majority of people to use vital government services. Digital ID will be mandatory for Right to... You are supposed to have an NI number to work in the UK. It's hardly likely that if the people who get the illegal immigrants jobs are going to be checking ID's.

I don’t want a coal powered one Dan!

How much? Walloping tree but nothing away.

The big choice is whether you go for a PROFESSIONAL range of saws like Stihl MS241, MS261 etc. These cost about £800 are solidly built, easier to replace parts, but heavier than a CONSUMER/PRIVATE saw. Consumer saws are lighter, less robust, but are much cheaper. For example the MS212 about £400. You could even go as small as a MS161 which costs about £150. This would only take a 13 inch bar though. I have a few of these cheap saws and if you took after them you can get 5-10 years out of them depending on usage. Any saw will die if you strain it or overheat it.

Wordle 1,560 4/6 🟨🟨⬜⬜⬜ ⬜⬜🟨⬜🟩 🟩🟩⬜⬜🟩 🟩🟩🟩🟩🟩

Morning all, Fine day again here. Wife’s birthday (state pension starts today), walk the dog, gardening with er indoors then meal out later. Happy Friday.

Lots and lots of everything.

Blunt spikes are dangerous and hard work. Sharpen them your self with a flat file on Buckinghams I just file two edges and remove the burr from the third edge.

Opposite buds fit the bill (ha!). I really don't know for sure, I reckon acer is a good shout. Bark looks like Rosaceae of sorts, or Lime, possibly even alder, but the buds don't fit the last two.

Quality as always mate.

Dont forget to register your gear on Steves Security Verification ARBSAFE.CO.UK If you scroll down it shows that kit has been recovered.

I think that only leaves Jaqui from Pentangle.

I dont think it has become a political hate forum at all. Yes some of the lounge threads can get a bit OTT at times but so what, Its the lounge section, ignore it if you must. The only way the forum can get back to the 'old days' of Arb/forestry/gear/woodwork talk if us as members move it in that direction by posting up new threads or resurrecting old ones. Forget the threads that annoy you, you wouldnt sit in a pub wasting your time listening to some shite on the next table if it didnt interest you. There are loads of members in here that are really helpful with vast amounts of knowledge, dont let a few posts/threads put you off.

I've had one for 5 years and it still decent. Yes it has its teething problems but ive done some decent size trees and felt safe and comfortable

I think that is Dyers Mazegill, non edible, but used for its dye, hence the name.

FFF&B this weekend end near Burford Next week National Hedgelaying Championships 2025 04/10/2025 08:30 - 16:30 £10 Waddesdon Manor, Aylesbury, Buckinghamshire, HP18 0JH Cotswold Comp in October CostswoldCompetition2025.pdf

Every days a school day! You never stop learning!

Perhaps if I were a rank amateur I'd go for that size. It's a retrieval ball for an item I haven't owned in years. Can't bring myself to get rid of it.

This is why forwarders got levelling rams tor the kingpost mount. The slewing is by rams working a rack against a smallish diameter ring gear, poor torque but if it's level and the load in free air no problem. My cranab 4510 exerts a fair slewing force for dragging long lengths but fails if it is not level, even with four 4" rams acting on the ring gear. A digger has a motor with a small gear working on a large diameter ring gear doesn't it? Big mechanical advantage.

There is nothing specific about this in legislation, and I am not aware of any case law. The LPA has 2 roles. It has to decide if the trees are important enough to be protected, this can be relevant to trees on and off site. If important they should be retained and protected. BS5837 etc blah blah. What is questionable is whether it should be protecting what amounts to encroachment and possible common law nuisance. It also has to decide whether the CA tree is so important for the amenity of the area that it should be TPOd. The reason is that generally a planning application replaces the need for a separate CA notification or TPO application. So it could TPO the tree and prevent any development that would harm it. This could exceed the RPA, which is really just a temporary made up thing that only preserves about 1/4 of the roots. Remember, CAs don't imply the trees are important. It's jsut a precaution to allow the LPA to decide if they are in the context of any threat to their remvoal or harm.

🧗🏼 1 x Climber 🦺 1 x Chainsaw Operative 📍Shrewsbury 📅 Monday to Friday, Days ‼️PTS Essential Ryan Spence 07502 101 847 [email protected] or Mathew Murphy 07543 666 315 [email protected]