Jump to content

Log in or register to remove this advert

niftysteve

Veteran Member
 View Profile  See their activity

  • Posts

    1,511

  • Joined

  • Last visited

 Content Type 

Everything posted by niftysteve

  1. niftysteve
    spotted a PTO version in a local fencing suppliers
  2. niftysteve

    660 :)

    niftysteve replied to jamesd's topic in Chainsaws

    mines on a 36 bar seems ok
  3. niftysteve
    depends if you are planning on doing a weekly round or going onto event sites some of the festival sites can cost upto £10 000 for the event , some sites also try and tell you what you can or cant sell ie a chip van also selling teas coffees
  4. niftysteve
    prob a fake husky for that money
  5. niftysteve
    would you do cash on colllection from your site id be interested in a couple of 3 ton loads collected from you
  6. niftysteve
    check engine oil level my entec chippit did the sam thing at the weekend when the chipper was nt sitting on level ground . it would start and run for a minute or so then die and stop. checked oil on level ground which was a tad low making the oil alert switch it off
  7. niftysteve
    has it got free wheeling front hubs if it has you need to twist them to the lock position to make the drive engage on the front
  8. niftysteve
    the materials from the local saw mill are more expensive than 17.50 /metre here prob nearer £30 /m including post mix any less than 70 a metre would not be worth doing the only way you can go cheaper is to buy the material in bulk ive a mate who does contracr fencing on large housing sites who buys in a lorry load most months,he can charge a fair bit less
  9. niftysteve
    £70 per metre all in unless there is some clearance to do first which would be extra
  10. niftysteve
    theres been a lot of dodgy items recently there have been two unimog s that the price is to good to be true and they ask you to e mail a seperate e mail address
  11. niftysteve
    sounds a bit like this stuff i got to clean the boiler heat exchanger at home i drove to st albens and collected it as they wouldnt post http://www.kamco.co.uk/GuidanceNotes/PDF/DescalingChemicals.pdf
  12. niftysteve
    if you could go without the truck for a few days get the injectors re furbished with new parts then they will be as good as new prob for less than new or just get a set from here http://www.ebay.co.uk/itm/Mitsubishi-Canter-2-8-TD-4m40-NEW-INJECTORS-SET-OF-4-/281264640986?pt=UK_CarsParts_Vehicles_CarParts_SM&hash=item417cadd3da
  13. niftysteve
    sell it cash on collection only when they come to collect it fire it up and run it through some timber
  14. niftysteve
    when the egr valve cracked on mine we tested for the head gasket and the tester gave a reading to say it had gone after stripping it apart we then found the cracked egr so loads of work for nothing
  15. niftysteve
    i had similar on my 3.0 rodeo turned out the EGR valve has a water jacket which split which then let water into the cylinders also if no turbo boost this can be the Air mass sensor failed
  16. niftysteve
    mine runs off a petrol hydraulic power pack it uses approx 1litre per hour
  17. niftysteve
    wolfie or peter haine will do a good job
  18. niftysteve
    get atowable field shelter for horse and rent out to horsey people
  19. niftysteve
    better off buying a bottle then you just pay the re fill cost and the bottle has its own regulator heres a link to there main site Cylinder Gases > Air Liquide UK
  20. niftysteve
    ive got an Esab 160 which runs on a 13 amp plug not the cheapest but welds just about anyhting i need too. i would go for a mig with gas
  21. niftysteve
    if the co op on histon road has them i ll get them
  22. niftysteve
    i ll call in as well i ll bring a bag of doughnuts for munchies
  23. niftysteve

    Crane?

    niftysteve replied to jody_h's topic in General chat

    http:// we used this guy to shift a digger from Leicester to Cambridge General Haulage - Ely, Cambridgeshire | Nigel Pindar Transport or these they shifted a 30 ft container into my neighbours back garden Transport & Crane Hire ? Cambridgeshire | C J Overy
  24. niftysteve
    check this horse powered mill [ame=http://www.youtube.com/watch?v=nbTNtCWXccQ]Horse powered saw mill, Belize - YouTube[/ame]
  25. niftysteve
    you would be better adding something like this Waterproof 12V Accessory Power Socket with Twist lock Plug - Marine 12 volt V B | eBay just take a live and earth from the existing reverse lamp maybe use LED lights as they draw less current

About

Arbtalk.co.uk is a hub for the arboriculture industry in the UK.  
If you're just starting out and you need business, equipment, tech or training support you're in the right place.  If you've done it, made it, got a van load of oily t-shirts and have decided to give something back by sharing your knowledge or wisdom,  then you're welcome too.
If you would like to contribute to making this industry more effective and safe then welcome.
Just like a living tree, it'll always be a work in progress.
Please have a look around, sign up, share and contribute the best you have.

See you inside.

The Arbtalk Team

Follow us

Articles

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.

  I accept