niftysteve
-
Posts
1,511 -
Joined
-
Last visited
Content Type
Profiles
Forums
Classifieds
Tip Site Directory
Blogs
Articles
News
Arborist Reviews
Arbtalk Knot Guide
Gallery
Store
Calendar
Freelancers directory
Everything posted by niftysteve
-
Steve As this thread is about Arbtalk this has just appeared on my of screen It's never happened before
-
these salso sell biocide ive just had to put in my mog as the filters were totally clogged seems to have worked so far Search Results for 'biocide' | Smith & Allan stock a wide range of oils and lubricants for car and motorcycle engines. Buy online now.
-
ive just put my 5 inch entec on ebay v twin kohler petrol engine still runs and chips well
-
i fitted a stove for friendswith a brand new eco house this has a whole house ventilation/heat recovery system of some sort fitted where it takes heat out of the say the kitchen when cooking filters the smells out and makes an even temp house
-
you might find a data plate on the back of the stove if its fairly new if not get a pic on here im sure someone will be able to id it
-
if it is a large enough chimney then yes when putting a liner down an existing clay lined chimney its near on impossible as the liner fills most of it you dont have to insulate but it can make the liner work better if you dont use vermiculite but use a pot hanging cowl they have a small air gap allowing an un insulated lined chimney the vent
-
my info came from the guy teaching the hetas coarse 4 1/2 years ago when fitting a stove you should use steelto close off the chimney (register plate) as if anything drops down the chimney it would break the hardi backer board and the use of a 5 inch liner is only permitted if using a defra stove with a 5 inch outlet if the stove has a 6 inch outlet defra or not it can only be used with a 6 inch flue you cannot go from 6 inch out of the stove down to 5 inch liner Im also a qualified HETAS installer and have never had any problems with stoves i have fitted when i have my yearly inspection
-
hardie backer board is not suitable,register plate should be minimum 1.6mm thick galvanised steel also when fitting the angle iron use the plugless concrete fixings (thunderbolts or similar )as the heat from the liner could melt a plastic plug
-
you can only use 5 inch flue if it is a defra approved stove
-
the guy i fit stoves with is also a sweep i he uses one called a sturdy vac like the one on the left on this link chimney_vacuums
-
chances are that if it was fitted to a boiler it will be the wrong grade of liner probably single wall flexi ,this is not suitable for solid fuel, twin wall flexi liner either 316 or 904 is what you need as this is rated upto 650 degrees
-
i can agree with you here i changed my 3 litre rodeo 2 years ago to a diesel dodge ram 2500heavy duty the last 2 years i have towed a 30ft trailer to southern germany the on board mpg gives a reading of 14
-
Acacia tree surgery Acacia Tree Surgery
-
theres a breakers i have used for parts for my shogun pinin that are pretty good at getting the parts out quick look up MITZY BITz heres a link Mitzy Bitz
-
the guy i fit stoves with uses this system Home seems pretty good the rods even sweep some of the awkward set ups people have with AGAS
-
if its based on the renault all of the variants with the same engine and gearbox did have problems with power steering racks going faulty and also gearboxs breaking as they were fitted with a car box rather than a van one
-
4 steel road pins also work well
-
Anyone know where I can get a couple of these hooks?
niftysteve replied to Sharkbait's topic in General chat
Buyers Products Weld-On Grab Hook-Fits 3/8in Chain #B2409W375 | eBay -
nfu at bury st edmunds are helpful
-
1 ton of 20mm stone will cover an area of 15 square metres at 35mm cover
-
Looking to hire a Firewood Processor - Sudbury / Suffolk
niftysteve replied to GTW's topic in Firewood forum
i think ben burgess at norwich hire one out Ben Burgess & Co - Horticultural and Garden Equipment Hire -
these are a decent arc welder ESAB Buddy Arc 180 Amp Inverter Stick / TIG Welder 240V | eBay
-
the fee varies depending on how much you put through its 2% ish to start with
-
ive just got a card machine they take a percentage depending on how much you put through it it does need an internet connection and juust plugs in the headphone socket on an i phone check out https://www.izettle.com/gb
-
same here usually dig out with the digger and ripper tooth
