Today's Posts

We won’t know unless they release the data you mong 🤷‍♂️that’s the whole point of the article ffs.

Is yours still doing what it says on the tin? @Mark Bolam

Of course... You're british,right?! 😁 Around here in Romania we have electric 2 wheel "things" going 90km/h on Highways... And it's worse the more East you "dare" to go... Basarabia/Moldova, Ukraine, God forbid you step into Russia... Anything is possible in Russia... Aliens are afraid to visit Russia... Anyway...

Lucky it didn't get propelled up the chute. A good reason not to stand in front of it and to keep the truck rear window protected.

162K views · 8.8K reactions | That’s two jobs he’s stolen from... WWW.FACEBOOK.COM That’s two jobs he’s stolen from Hillary Clinton. https://docs.house.gov/meetings/JU/JU08/20250227/117951/HHRG-119-JU08-20250227-SD006-U6.pdf https://x.com/realblaines/status/1989530490303647934?s=20 LOL.

Thanks Guys, the only saving grace is I have an old unit that the bearings in the head have gone.. should be able to just swap the heads over if drying out doesn't work

Having olives and lemons and that is nice like, but I'd rather they couldn't grow in this country. We're starting to get viable vineyards around the place as well now.

What have you got?

Thank you all for your kind replies. Appreciate it! Photo attached. No TPO.

Too many choices today. Wordle 1,611 5/6* ⬜⬜⬜🟨⬜ ⬜🟩⬜⬜🟨 ⬜🟩🟩🟩🟩 ⬜🟩🟩🟩🟩 🟩🟩🟩🟩🟩

Sorry, this is a British forum (.co.uk); people here won't try to advise you. All we can recommend is finding locally appropriate advice. Good luck.

Crytec do one that's not much bigger, bit wider but presume it have to be to go road speed. Would think this is about as small and cheap as road tow get. Chinese made obviously so prob not full time commercial quality; https://crytec-power.co.uk/products/crc500h-r-hydraulic-feed-wood-chipper

IMG_6112.mov Sailor just being a fine figure of a dog on the penultimate drive today. Tied up because he’d just tested my patience on some bloke’s labrador and I needed to drop a length of fencing during this one anyway. His best work went unrecorded because I was too busy laughing a rib out. Big field of waist-high dead peas. Woodcock up straight away. Then zigzagging like he knows what to do, three or four pheasants. I praise him and riding high on the adrenaline and my satisfaction he bounces across the field like a blesbok, springing three feet straight up and down, not in slow motion but as if the world just stopped for a moment to marvel at it. Magnificent. Pissed myself to the point I couldn’t blow the whistle.

Can you give an idea of the day rate please?

And a really fcking good guitarist. Really rhythmic, while singing something totally different (well). Not easy. https://youtu.be/TMGJhPO0fUo?si=ToB-03PocWMUC29u and to a lesser extent, Shy. Tom Morello is often held up as an inventive guitarist (not virtuosic in the classical sense but doing things other people don’t do, usually rhythmic). I think Ani could teach him a thing or two.

If you block the fuel inlet to the carb, just put your thumb over it and create a vacuum on the primer side, put some fuel pipe on it and suck you should not be able to draw air through, if you can you either have a hole in the pump gasket or usually a bad check valve.

As Stubby said it was user error rather than a manufacturing issue. The 395XP is a really good saw. I have a brand new one knocking about that has a cracked crankcase, I should really sell it on or fix it up. It will be the last of the 395's.

Hi, We are looking to hire a tree surgery assistant groundsman. Based in oxfordshire we also cover buckinghamshire, reading, milton keynes, greater london and london . Must have qualifications and experience as well as drivers license. feel free to get in touch via Whatsapp on 07831 693280

You could start an eBay shop.

It's taken a while - we now have 1/4 drive sprockets for the 540XPs. These are exclusive to us. No one else has them in the world (as we developed the mold for them). What this means is you can run 1/4 .043[1.1mm] chains on your 540XP. AND you could also run carving bars - the sprocket will run both 1/4 .043[1.1mm] and 1/4[1.3mm]. Find the sprocket here: 5774897-08Q Spur Sprocket 1/4 x8 tooth [Husqvarna T540XP, 540XP Mk I, II, III] WWW.CHAINSAWBARS.CO.UK 5774897-08Q Spur Sprocket 1/4 x8 tooth [Husqvarna T540XP, 540XP Mk I, II, III]. Allows you to run Dime tip carving bars and... Find the sprocket removal tool here: 4507 [502 54 16-03] Husqvarna Sprocket Clutch Removal Tool WWW.CHAINSAWBARS.CO.UK 4507 [502 54 16-03] Husqvarna Sprocket Clutch Removal Tool [42, 242, 340, 345, 346, 350, 351, 353, 455, 460, T540 XPs]... Bars - go for one of these here: Tsumura 1/4 .043 Black Edition - Chainsawbars WWW.CHAINSAWBARS.CO.UK And watch the video here please - shows fitting and other info:

Turns out it is the X having checked, so must be the same as all others. Cheers

Yes. When wood smoulders, with no flame burning the offgas, what is happening is the fire is hot enough to pyrolyse wood but not hot enough to reach the autoignition temperature of the offgas. Nascent char is oxidising to give off enough heat to sustain its combustion but largely without flame . Thus the acrid smoke going up the chimney condenses on the cold chimney as pyroligneous acid. This can eat mortar. I think it is slightly worse with hardwoods as it contains acetic acid (wood vinegar). Before organic chemistry took off pyrolysing beech was a major source of acetic acid. In 2002 I was snagging a large woodchip boiler at a department store in Milton Keynes where they had been burning rejected/returned flat pack furniture and one part of the flue had become too cool. Here is a picture of a 316 stainless steel single skin pipe that had been perforated by the acid that condensed, though in this case I think it was probably hydrochloric acid from some plastics that were associated with the furniture.

It keeps popping up doesn't it.