kinderscout
-
Posts
371 -
Joined
-
Last visited
Content Type
Profiles
Forums
Classifieds
Tip Site Directory
Blogs
Articles
News
Arborist Reviews
Arbtalk Knot Guide
Gallery
Store
Calendar
Freelancers directory
Everything posted by kinderscout
-
To me, looking at the damage it looks like one of the needle bearing has come from some where.?
-
Had a good day today milling ash and sycamore 22 boards in all.hopefully will manage to mill the rest tomorrow.
-
Granburg chain is very good but you will need the granburg sharpener to sharpen it. see chainsawbar .com
-
Unfortunately it 50 miles from me. Thanks for all your views on this think we are all of the same view which helps a lot .
-
My trailer has the lockable hitch and the rear has a BQ £20 multi strand cable fastened to the wall
-
No this is all I have Steve just the two photos. I just don't want to wast the man's money milling it . from my experiences it just does not look right with all that sap wood.
-
I have beeno asked to mill this oak that's fine, but I don't think it is English Oak I think it is turkey oak what's your thoughts on this.
-
I cut at 2 1/4 or 2 1/2 to allow for shrinkage and planning and 10 ft long as I can manage to carry that on my own .
-
It was back in the 1980 s over a large band sawmill with a six inch wide band largest mill I have ever seen.
-
This was just a zinc canopy the length of the michine but over the exhust of the engine about 6 inches wide on to a what looked like a 9 inch flue pipe centre location.
-
Seen this sort of set up before and it had a canopy much like a snooker table with a chimney on.enabling the mill to travel.
-
18 ton on ebay in Southampton says fire wood but some of it looks quite nice.worth a look.
-
Sussex model centre surply some good quality two pack resin. usually surplied in setting time 5 min 10 min 30 min etc.
-
Would two clutches of a chainsaw make suitable bearing. cut the wall off and use the back plate and needle bearings.
-
It was last run and used about 18 months ago. looking at it,it's in a good condition.engine turns over very positive on the pull cord,nice compression.
-
At a farm today and he pulled this state of the art machine out. And the farmer wood like to know a bit more about it?
-
Thanks Alec. I put a offer in on some oak on ebay and was told it was poor offer and by what you are saying it was a good offer. I can hold my head high.
-
No in the round stem
-
I am right at between £6 and £20 per cubic ft wet timber
-
Your message box is full if you give us a ring on 07854568897 Carl
-
I have a huqvarna 3120 up for sale 2 bars and several chains 07854568897 carl
-
Husqvarna 3120 new 50 inch cannon bar and 42 husqvarna bar six milling chains and a some spares. I have just bought a new 880 so this one can be sold. Saw has had a rebuild with new head,exhaust.clutch springs etc. so a new saw.Offers 07854568897.Carl
-
Very Sad news, very talented man .Rick was also a very good craftsman,and was a good Rc model flyer.I learned this many years ago looking at a quarter scale model stearman which Rick had built.
-
Unusual for me to buy a bowel, as I usually trade with people but liked this so much,turned by Pete fox of fox furniture it is a 19" platter in lyme.
-
Quality and looks is everything with the oak boards,I would cut the boards at 2 1/4 to 2 1/2 thick allowing for shrinkage and finishing. A really nice board at 8' long 30"wide I would expect to get £80 to £100.
