amfell

try Meetens on 01772 691604 Meetens specialising in petrol and diesel engines and spare parts for industrial machinery or Uni-power on 01371 875331 Uni-Power | Briggs | Honda | Kohler | Kubota | Lombardini | Peerless | Tuff Torq | Yanmar

the official service bulletin from Husqvarna re poor idle 550 idle cure.pdf

525 39 68-02 inlet pipe assy 577 40 64-02 hose

part number 506 22 99-12 current price £300.55+Vat

the tool you require is an MTD part number 797-00039 best of luck in finding one I could only find one available in the uk on diyspareparts.com for the reasonable price of £47.78 a search reveals that the sale of the tool was banned by the EPA in the states to stop the unauthorised twiddling of the mixture screws by non service personnel

the windvane is connected to the choke shaft there is a bit of adjustment with putting the spring in different holes on the choke / governor lever the governor system was used mainly on the TS350 to presumably prevent "overspeeding" the abrasive disc the Max engine Rpm is 10,000 acording to the WSM but there is no mention of the theory of operation of the governor

a quick google produced these http://www.rfs.nsw.gov.au/__data/assets/pdf_file/0012/42303/OP-1.3.1-Hazardous-Trees-and-Appropriate-Use-of-Chainsaws.pdf https://public-library.safetyculture.io/products/sem0701-chainsaw-risk-assessment http://www.rapidhire.net.au/wp-content/uploads/2015/03/combined-safety-documents/Chainsaw.pdf

have a look at HLE | Harrison Lubrication Engineering | Oil and Grease Lubrication Systems AKA the nipple shop they also do centralised greasing kits

503 92 53-05 complete crankcase including bearings but no seals or gasket £163.40+vat

straight off husqvarna's price list

the flange is 503 92 85-02 at a price of £2.36 + vat the intake boot is 503 92 87-02 £ 11.02 +vat

Have seen on a 550xp which is basically the same construction the 2 crank fillers have a plastic insert that partially melted and allowed them to rattle against the crank root cause put down to a big-end bearing that nipped and over heated 1 replacement crank assembly later all sorted

from page 32 of user manual 1/4 pitch sprocket A556-001710 20CM guide bar C20H25-52CL-ED 25CM guide bar C25H25-60CL-ET

if you are getting it dipped check if they are using caustic soda (sodium hydroxide) as this will dissolve the aluminium and release dangerous hydrogen gas

if you have a look at this Gates publication you will see there are more than just A, B & C section belts the US tends to use 4L & 5L on a lot of US produced machinery http://www.gates.com/~/media/Files/Gates/Industrial/Power%20Transmission/Catalogs/BELT%20ID%20CHART%202012%20SM.pdf there is also a horticultural catalogue http://www.gates.com/~/media/Files/Gates/Automotive/Catalogs/Automotive/Grounds%20Maintenance%20Equipment%204312061.pdf

they have gone into liquidation Meetings of Creditors MISTER SOLUTIONS LIMITED (Company Number 05971051) Registered office: Sterling House, Mandarin Court, Centre Park, Warrington WA1 1GG Principal trading address: Unit 7, Sneyd Business Park, Sneyd Street, Stoke on Trent ST6 2NP Nature of Business: Online Retailer Notice is hereby given, pursuant to Section 98 of the Insolvency Act, 1986, that a Meeting of Creditors of the above-named Company will be held at Parkin S Booth & Co., 2 City Road, Chester CH1 3AE, on 24 February 2015 at 11.15 am. The purpose of the meeting, pursuant to Sections 99 to 101 of the Act is to consider the statement of affairs of the Company to be laid before the meeting, to appoint a liquidator and, if the creditors think fit, to appoint a liquidation committee. The resolutions to be taken at the meeting may include a resolution specifying the terms on which the liquidator is to be remunerated and the meeting may receive information about, or be called upon to approve, the costs of preparing the Statement of Affairs and convening the meeting. In order to be entitled to vote at the Meeting, Creditors must lodge their proxies, together with a full statement of account at the offices of Parkin S. Booth & Co., 2 City Road, Chester CH1 3AE, not later than 12 noon on 23 February 2015. Ian C Brown (IP Number 8621) of Parkin S. Booth & Co., 2 City Road, Chester CH1 3AE, is a person qualified to act as an Insolvency Practitioner in relation to the Company who will, during the period before the day of the Meeting, furnish Creditors, free of charge, with such information concerning the Company’s affairs as they may reasonably require. E-mail address [email protected]; Telephone Number 01244 340129 Jane Holtham, Director 23 January 2015

the spring that you pointed to in the video clip looks to be stretched too far, both pawls should move easily the pins they are mounted on are press fitted into the flywheel, they can be punched out from the back side of the flywheel the central hub of the rope pulley should have a series of fine grooves the pawls tend to wear a central band around the hub I have heard of one repair that replaced the steel straight knurled hub with a new one that was manufactured on a lathe, the serrations were made by a lathe tool being wound across the outer diameter to cut a single groove, the chuck was then rotated by hand a little and the next groove cut ( not a cost effective repair but replacement parts were NLA back in early 90s )

I have found a pdf copy if you PM me your email address I will send it to you I have had to break it down into 10 parts as it is too big to email as one file ( 10.5Mb) Andy

you will need a Pinhole Yoke there are different diameter shafts ( both Inch and Metric sizes) they also increase in size due to Horsepower ratings the fitting of a yoke is a bit of a fine art if you have not fitted one before , you can do it with a hammer and a punch, but there is always the risk of damaging the UJ cups or trapping a needle roller as mentioned above your local AG dealer should be able to assist they should keep the oval tubing in stock to replace bent shafts you might need advice to see if your current shaft will stand the HP of your Mog

finding new parts for a dolmar 123 might be awkward you might have more luck finding the side cover from a 309 dolmar disc cutter the exhaust from a 309 will fit but you might have to modify the outlet as it exits out sideways rather than angler 45 degree to the front ( it might need shortening to miss the chain brake handle lever

Shindaiwa tools are part of the YAMABIKO Corporation along with Echo in the UK the distributor is Countax there are distributors in these countries in Europe | Austria | Belgium | Czech Republic | Denmark | Estonia | Finland | France | Germany | Greece | Ireland | Italy | Luxembourg | Netherlands | Norway | Poland | Portugal | Russia | Spain | Sweden | Switzerland | Ukraine | United Kingdom if you do a google search for shindaiwa IPL it brings up the usa site with illustrations of the different models attached is the IPL for the C282 I could only find spares prices on a US site complete gearbox assy = $180 SHINDAWA_282_PARTs.pdf

parts missing from your T20 should be available from Rowena motors WZ (2 different versions ) type WZ-19 item no desc part no 4 Cover - Air Cleaner 21-446 5 Cover - Assembly Pump 21-777 (broken bit should have black primer button on it ) 34 Filter - Air Cleaner 125-50 40 Plate - Air Cleaner 157-250 unfortunately spring and fixing screws shown as not avalable but an assorted box of metric screws should provide replacements or type WZ-26 item no desc part no 4 Cover - Air Cleaner 21-470 5 Cover - Assembly Pump 21-777 (broken bit) 27 Screw - Air Cleaner 96-577 28 Screw - Air Cleaner 96-338 31 Spring - Filter 98-3018 34 Filter - Air Cleaner 125-50 40 Plate - Air Cleaner 157-250 for how it works http://www.walbro.com/media/21922/WZseries.pdf‎ for info on all walbro carbs http://www.walbro.com/media/21936/SERVICEMANUAL.pdf

a site i use called Abebooks lists 2nd hand and out of print books from sellers all over the world http://arbtalk.co.uk/forum/general-chat/74508-blacksmith-book-search.html revealed loads by different authors THE BLACKSMITH'S CRAFT by Tech. Officers at C.o.S.I.R.A.: Council for Small Industries in Rural Areas 1979 9th. impression - Culinary Jottings is the specific one you mentioned £14 + £3 postage

J S Cole, Haverthwaite Ulverston; 01229 582149 Gilbert Brown & Son, Hawkshead; 015394 36480