Jump to content

Log in or register to remove this advert

Jase hutch

Veteran Member
 View Profile  See their activity

  • Posts

    1,162

  • Joined

  • Last visited

  • Days Won

    1

 Content Type 

Everything posted by Jase hutch

  1. Jase hutch
    I'm doubting myself now.. Please can anyone else confirm ?
  2. Jase hutch
    Pete B would know cos he's sales and they're always nicking keys..?
  3. Jase hutch
    That looks like the right one to me..
  4. Jase hutch
    The solenoid valve is under the infeed chute and you need to check for magnetism on the nut that holds the coil on. It's a 12mm nut (19mm spanner size).
  5. Jase hutch
    Hi Mitchel, do you get a green light on the 'No-stress' box at full engine revs ? If so, do you then get magnetism on the 'No-stress' solenoid valve ?
  6. Jase hutch
    Yep all good now , cheers Steve.
  7. Jase hutch
    Not for me.....
  8. Jase hutch
    Wasn't it an 'English spec' chipper as it was bought in the UK..? It's simple enough to fit the extra palm switches though..
  9. Jase hutch
    I'd say it started about a week ago..
  10. Jase hutch
    Funny that, I've got exactly the same problem...?
  11. Jase hutch
    Good advice above and I would also spend a little time and get that blade to shearbar gap set up correctly. Jase.
  12. Jase hutch
    Ok mitchel, firstly , there's an override tap under the infeed chute for the no-stress, it should be open , ie the handle on the tap should be in line with the fittings on the tap. If you run the machine do the rollers stop on tick over with a red light and start at maximum engine revs and a green light ? If they lack power you could try turning the override tap lever to see if thus improves the power but be prepared to push the red safety bar into stop if the engine gets close to stalling. Let me know how you get on.. Jase.
  13. Jase hutch
    Ha ha.....
  14. Jase hutch
    Hi Dan , yep I'll be there on the stand on Thursday and just browsing on Saturday with Mac the Legend....
  15. Jase hutch
    The ticket says, 9am-6pm each day..
  16. Jase hutch
    You could try Bryco , I'm just sat eating lunch and my Bryco mug shows them as a Yanmar dealer.. 01327876166 and ask for Paddy , he's a top bloke and if the gaskets aren't available then I'd ask him for his opinion..
  17. Jase hutch
    If you're after a genuine gasket you could try 'Engines Plus', they're based in Gloucestershire and are the importer for Isuzu and Yanmar and a great company to deal with..
  18. Jase hutch
    You are missing the 'extension piece ' which is basically a twisted piece of heavy gauge wire , it pushes over the fuel tap which is buried under the fuel tank and comes out through the rubber grommet in your picture allowing easy operation of the tap. The part will be readily available from any 'Briggs' dealer..
  19. Jase hutch
    GreenMech had this problem years ago and resolved it by welding in a thicker piece of steel onto all square section discharge chutes..
  20. Jase hutch
    Ace stuff...?
  21. Jase hutch
    Wot..are you coming over ..?
  22. Jase hutch
    GreenMech sell them and Toro are GreenMechs dealer in Australia so maybe give them a try ..?
  23. Jase hutch
    The torque has been increased to 200Nm with the introduction of the Nordlock washers...
  24. Jase hutch
    No need to replace the bolts unless something has been through the chipper and caused damage, then it's advisable .. It's recommended to replace the nylocs each time but personally I just go on feel with nylocs.. If your chipper has the 'Nordlock' washers fitted under the nylocs (two part serrated washer) then make sure they go back correctly with the course serrations together and torque the nuts up to 200Nm... Jase..
  25. Jase hutch
    If you think you'll use the turntable then I'd go with the Quadchip otherwise I would choose the Arb 150..

About

Arbtalk.co.uk is a hub for the arboriculture industry in the UK.  
If you're just starting out and you need business, equipment, tech or training support you're in the right place.  If you've done it, made it, got a van load of oily t-shirts and have decided to give something back by sharing your knowledge or wisdom,  then you're welcome too.
If you would like to contribute to making this industry more effective and safe then welcome.
Just like a living tree, it'll always be a work in progress.
Please have a look around, sign up, share and contribute the best you have.

See you inside.

The Arbtalk Team

Follow us

Articles

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.