Jump to content

Log in or register to remove this advert

cornish wood burner

Veteran Member
 View Profile  See their activity

  • Posts

    1,500

  • Joined

 Content Type 

Everything posted by cornish wood burner

  1. cornish wood burner
    If that's red I'd like to know the supplier please
  2. cornish wood burner
    Just a word of warning about remote control of biomass boilers. It's best to control it in the flesh as it is difficult to see remotely what the fire is doing. We had damage done to ours when it was controlled from Austria. If I knew then what I know now I wouldn't have allowed it. Local is best and a visit is worth the extra if it is a setup issue.
  3. cornish wood burner
    Why not start with your own wood but buy a lorry load from your local cutter as soon as you can afford it from your sales. If you struggle to find a cutter then try euroforest or whoever is your local timber middle man. If you source small diameter cord it would make splitting easier and would be quicker to season as a bonus. If you have seen any timber lorries around your area make a note of them or try the Internet and give them a call. They would no doubt help you with some contacts. Stack your cord where the wind can blow through and ideally cover the top for best results.
  4. cornish wood burner
    Filled most of my saws strimmers and hedge cutter with aspen before the winter. Sub 35cc seemed to need a 1/4 turn of the L screw but my 40 to 60cc seemed fine as they were. I don't know wether that's the luck of the draw or a general trend. The only problem was with my MS211 which needed a tweak on the L then seemed fine, however I picked it up a few months later to finish a job rather than mix more petrol oil and it was down on power. Not had a look yet, might try a fraction on the H screw as a start.
  5. cornish wood burner
    Put washing powder in next time? Wash something a bit less dirty like normal work gear after to clean up the machine.
  6. cornish wood burner
    50 years ago I used swing the blower handle for a blacksmith. He used to make the horse shoes rather than buy them as is normally done now. Graduated to making the shoes and many other things for him. When he retired we took over his forge and used it as part of the workshop equipment. Over the years we used it to make many things and for a heat source to straighten many heavy pieces of steel when the oxy acetylene wasn't up to the job. It's amazing to see a big a piece of steel come out of a big coal fire glowing white hot. Over the years in my engineering career I have used welders lathes,mills grinders etc etc but none compare to the satisfaction of using the old coal forge. It seems to have a character that is missing with gas. If you ever get the chance to buy or build one imo it's well worth the extra bit of time to light it.
  7. cornish wood burner
    I too have tried spreading and drying G50 but only a thin layer seems to dry. Might be worth trying a deeper heap to generate a bit of heat and steam off the moisture. That seems to work in our shed to some degree if it is pushed around enough. Some years ago I did read of a trial (in Austria I believe )where they heaped and covered with a breathable membrane to lose the water
  8. cornish wood burner
    The tree surgeon chip I have seen is normally small as you say. If the boiler uses G30 it will be quite small and chances are the size will be ok providing no out of spec long pieces. Greenery it not good as biomass boilers have several pressure, temperature and O2 sensors sensing pipes etc which could get a tar coating when burning wet or green material. That said we have burnt wet and green material but our boilers will be much bigger with a bigger mass so resistant to a slug of wet material. We would mix with dry material anyway. Your engineer is right to be concerned but it depends on quantity of yours and their material.
  9. cornish wood burner
    Need to gear it down a bit more, a saw would run several times faster than a mower engine. I use a complete ride on to tow an arb style trailer for my firewood. Been known to drag a bigger twin wheel trailer on occasions Have a look at the picture in the maintenance section petrol how old is old. Barrie doesn't approve though
  10. cornish wood burner
    He will gain that sawdust. Consider 75 metres of timber gives 300 logs @250mm long In 3metre x 25 lengths needs 275 cuts In 2.5 metre x 30 lengths needs 270 cuts He will save those 5 cuts for the same number of logs so no cause to feel short changed
  11. cornish wood burner
    Thats exactly what we decided today. Diesel mulcher diff lock or even better 4wd The iseki range looks interesting with front decks and 4wd as choices. Presumably they mulch ok.
  12. cornish wood burner
    My lawn at home has never looked better since buying a mulcher so I totally agree with your comments Barrie. Personally I would never go back to a collector. I can see price is going to be an issue for the company so I expect compromises will need to be made.
  13. cornish wood burner
    Thanks for all the answers guys, much appreciated
  14. cornish wood burner
    Heat is exactly why a mains unit should be used whenever possible 12v Units are made smaller to be portable so are not so good at heat dissapation which is a result of compressing the air
  15. cornish wood burner
    12v dc and 230v ac obviously are totally different motors. You need an inverter or transformer/rectifier to change voltages depending on which way you go. Whether it is built in or separate it will be expensive. Why not get one of each? The AC would almost certainly have more output and the DC portable. The cost of the two would almost certainly be cheaper than a dual voltage machine even in the unlikely event you could find one.
  16. cornish wood burner
    Thanks David. Just had a look on gardenkits web site and there was a JD mulcher there.
  17. cornish wood burner
    OK Getting convinced on Countax quality or lack of. Normally new but I wouldnt rule out demonstrator type hours. I need to put a budget figure in next years expenditure. Probably most important to pick the right machine and argue about money at the meeting. £8 to12k but nothing is set in stone.
  18. cornish wood burner
    Sounds good. Do you happen to know if they do a mulcher version?
  19. cornish wood burner
    Thanks. Fair point about the domestic mowers. I don't think the mulching is negotiable though. Simplicity mulcher is used at the moment but a bit more area will be added soon so I have been tasked with finding an upgrade.
  20. cornish wood burner
    I'll have a look thanks Barrie. Really ought to be diesel though as we have it on site and fetching petrol in cans is another job on a long list. BTW. I did sense your slight dislike of Westwoods transmissions yesterday. I sort of agree as a couple of the most used mowing gears are showing signs of wear on my machine and I did have to replace a half shaft on the one at work but that had reason to shear unlike the lightly used one in my picture. Normally I do use a smaller two wheeled timber style trailer but I had a lot to shift that day.
  21. cornish wood burner
    Thanks looks a good machine. Didn't mention a mulching deck in the brochure. Presumably they do one?
  22. cornish wood burner
    Thanks I'll contact him
  23. cornish wood burner
    I've heard he knew a bit about them. If he's not too far from Plymouth I might take a trip to see him. Thanks
  24. cornish wood burner
    I need to price a good quality ride on mower. The spec is No timed blades as tooth belts can jump when obstacles are hit. About 4 acres to be mowed. Lawns and paddock, a little area might be cut up and down as a bit steep to cut across. Diesel, hydrostatic, mulcher with an occasional pickup facility. Fairly maneuverable but no really tight areas. Price not so important as quality and performance. One thought is the Countax A series, any experience of these. Thanks
  25. cornish wood burner
    It just needs seasoning. The reason for the avoidance of conifer woodchip is the resin. It can stick chip to sensors and stop the feed transport. I normally try to keep it a couple of years before chipping to minimise this problem. If I need to get my Rayburn hot then leylandii works well.

About

Arbtalk.co.uk is a hub for the arboriculture industry in the UK.  
If you're just starting out and you need business, equipment, tech or training support you're in the right place.  If you've done it, made it, got a van load of oily t-shirts and have decided to give something back by sharing your knowledge or wisdom,  then you're welcome too.
If you would like to contribute to making this industry more effective and safe then welcome.
Just like a living tree, it'll always be a work in progress.
Please have a look around, sign up, share and contribute the best you have.

See you inside.

The Arbtalk Team

Follow us

Articles

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.