needenginerunnin
-
Posts
98 -
Joined
-
Last visited
Content Type
Profiles
Forums
Classifieds
Tip Site Directory
Blogs
Articles
News
Arborist Reviews
Arbtalk Knot Guide
Gallery
Store
Calendar
Freelancers directory
Everything posted by needenginerunnin
-
blocked breather in fuel filler cap, when it dies take cap off and listen for a rush of air in bound.
-
could you not have cast your 4x4 side ways with your jack, or lift it up and tie two posts together under each wheel.
-
may be this is what the op was selling.
-
how many hp under the hood on your tablesaw?
-
these guys do just about everything poly tunnel. Highland Polytunnels / Super Strength Garden Polytunnels no connection to me and I have never used then, but do have a good range.
-
one swallow doesn't make a summer, but it does make for a good evening.
-
top job, always more work than first thought. would there be any chance of a picture with the trailer empty, no worries if not.
-
298xp my first saw, evan tho it doesn't have a decompressor:001_smile:
-
Hydraulic guillotine style firewood processors
needenginerunnin replied to tcfengineering's topic in Firewood forum
can you explain more -
as far as I am aware for the better part of ten years now and on a fair few car engines the alternator does not control the battery light on your dash direct, the ecu passes the message on etc. gone are the days of kiss engineering. Lucas acr series and bosch alt's that lasted for ages. needenginerunnin
-
anybody watching This Farming Life bbc2
needenginerunnin replied to needenginerunnin's topic in The Lounge
Lady Lairds anybody watching this as well, bbc scot only, but on I player. BBC One - Lady Lairds, Episode 1 -
Germany, Sweden did have road tax for trailers don't know if they do now.
-
BBC Two - This Farming Life beats country file any day.
-
Hydraulic guillotine style firewood processors
needenginerunnin replied to tcfengineering's topic in Firewood forum
[ame= ] [/ame] 1m split, needs some redesign. -
Hydraulic guillotine style firewood processors
needenginerunnin replied to tcfengineering's topic in Firewood forum
[ame= ] [/ame] -
i'll go with that as well.
-
as far as I know you didn't need to only .410 is bore rest of sizes are gauge. https://en.wikipedia.org/wiki/Gauge_(bore_diameter)
-
no, but thinking about it. they look a good design, simple.
-
12 gauge
-
if you look at the cutter its tapered at start so it will cut metal out before a straight barrel bit for evan finnish.
-
no walkies needed, just what big cats leave behind in steaming piles. It works in Sweden so don't see it wouldn't over here:001_smile: it would be a crap job, but cheap and trees get fertilised as well. sprinkle around the boundary hopefully job done, despite its been awhile since big cats roamed these shores deer and the like still give anything big cat related a wide birth. needenginerunnin
-
corco2000 do you have a zoo near to you? not a wind up, I am being serious.
-
pto hydraulic pump instead to get the best, compact tractor flow rates can be a bit on the low side.
-
[ame= ] [/ame] little else needs to be said. needenginerunnin
-
its to do with evolution and the design. the old landy hasn't changed that much in the last 70 years, while cars have changed lots, in the way they are nailed together so to speak. in a word landys are crude and simple 'KISS' if you like, which is a blessing and there down fall. they are easier to bodge than most and it gets them a bad name, not the landys fault. yes odd bits fall off at almost any age, but you find me an other motor that comes close to matching it for what it has and can do. not too many 1980's 4x4 about. while modern 4x4 can out preform on the road they cant do short runs with out warning lights flashing and a computer upset. evolution backwards. and to date I haven't seen a jap 4x4 owner club thread on arbtalk. needenginerunnin
