Best process to finish and treat elm timber

[Steve Bullman]

All done! Recessed the legs…bit scruffy but no ones going to see it. Had to stick a spacer under one leg to get the table even.

Thank you all for your advice 

 

 

 

[muttley9050]

Lovely work Steve.

[Steve Bullman]

Onto the next project and preparing some yew for console tables. Need to sell a couple of these now so I can put all the tools I bought through the books 😀

[gary112]

  On 15/01/2022 at 19:57, Steve Bullman said:

Onto the next project and preparing some yew for console tables. Need to sell a couple of these now so I can put all the tools I bought through the books 😀

Expand  

Some nice boards there Steve,your getting into this now i reckon😂

[Steve Bullman]

Thinking about getting a bit more adventurous for my next project and making an indoor slide out of Yew for the little one, something similar to this.

What would be the best finish for it to make it nice and slippy?

[Dan Maynard]

  On 15/01/2022 at 19:57, Steve Bullman said:

Onto the next project and preparing some yew for console tables. Need to sell a couple of these now so I can put all the tools I bought through the books [emoji3]

Put your work laptop on it for a while, becomes office furniture so you can put the wood and legs through the books too.

[ucoulddoit]

  On 16/01/2022 at 16:14, Steve Bullman said:

What would be the best finish for it to make it nice and slippy?

 

Expand  

As there hasn’t been any response yet, I’ll suggest a hardwearing finish like polyurethane. An oil finish on yew looks good. So instead of using a brush, you could make a 50/50 mix of polyurethane and turps then apply it with a rag like an oil finish, i.e. wipe it on, leave for a few minutes to soak in, then wipe off what’s left on the surface. I’d start with say three coats and see how it looks. 

Andrew

[Stubby]

  On 16/01/2022 at 16:14, Steve Bullman said:

 

What would be the best finish for it to make it nice and slippy?

Expand  

Possum grease . 😀

[MattyF]

  On 18/01/2022 at 06:34, ucoulddoit said:

As there hasn’t been any response yet, I’ll suggest a hardwearing finish like polyurethane. An oil finish on yew looks good. So instead of using a brush, you could make a 50/50 mix of polyurethane and turps then apply it with a rag like an oil finish, i.e. wipe it on, leave for a few minutes to soak in, then wipe off what’s left on the surface. I’d start with say three coats and see how it looks. 

Andrew

Have you any pics of timber finished this way ??
I'm looking for a hard finish on woods but have never used a polyurethane or acrylic finish.
My thought on yew is that oils tend to turn it brown and loose the reds , I would like to keep yew as natural as possible to its final finish after sanding and preserve those colours if that's possible.

[ucoulddoit]

  On 18/01/2022 at 11:11, MattyF said:

Have you any pics of timber finished this way ??
I'm looking for a hard finish on woods but have never used a polyurethane or acrylic finish.
My thought on yew is that oils tend to turn it brown and loose the reds , I would like to keep yew as natural as possible to its final finish after sanding and preserve those colours if that's possible.

Expand  

I've not used it on yew but can't see why it shouldn't work. I'll post some pics in a day or two when I've time to take them. It was a tip I got from a 'well known' Yorkshire furniture maker I met at the Harrogate woodworking show years ago and was his method of finishing dining tables.

 

Andrew