sandspider
-
Posts
1,775 -
Joined
-
Last visited
Content Type
Profiles
Forums
Classifieds
Tip Site Directory
Blogs
Articles
News
Arborist Reviews
Arbtalk Knot Guide
Gallery
Store
Calendar
Freelancers directory
Everything posted by sandspider
-
No, just dismantled it and lots of carb cleaner. However, it did run for a bit after cleaning, to the extent I could do a bit of strimming with it.
-
Sorry guys, I still can't get the bugger working! Any.more suggestions please? I reset the carb to default settings (that may have been a mistake!), but after some tweaking I can only get it to run very briefly (a second or two) on WOT. Same whether choke is on or off. Spark plug is new, air filter is clean, fuel lines are solid, carb is rebuilt and cleaned. Fuel appears in the primer bulb, and stays there. A little.bubble.of air at the top of the bulb. If I push the bulb again it may run for another stroke.or two.but not much difference. Fuel is fresh. Any more thoughts before I chuck it and buy a florabest?! I can't remember exactly where the carb screws are in the end, but it doesn't seem to make much difference anyway. I tried a couple of local service places, and the only.one to get back to.me.is a six week wait and 35 quid.minimum.just to look at it!
-
Hi all As above. I'm looking for a good local place to do the bits to chainsaws, strimmers, mowers etc. that I can't or won't do! Google isn't very helpful, and I'd rather have recommendations. Cheers.
-
Retirement plans, perhaps to include planting a "forest"
sandspider replied to difflock's topic in General chat
Black / false locust is Robinia pseudoacacia. I've got a load in pots at the moment, which will be going out in to my paddock soon for eventual firewood coppice. Certainly seems to be fast growing, and is an attractive tree. Should also be reasonably OK if temperatures increase in future. But it is non native and spikey, and apparently suckers quite vigorously. -
Firewood coppice / pollard - short, thick stems
sandspider replied to sandspider's topic in Firewood forum
Makes sense, thanks OSM. Will try a few different approaches... -
Firewood coppice / pollard - short, thick stems
sandspider replied to sandspider's topic in Firewood forum
Might give it a try and see how it goes. -
Firewood coppice / pollard - short, thick stems
sandspider replied to sandspider's topic in Firewood forum
Hmm. Good point. Maybe not worth the extra trimming of side shoots. -
Morning all. Had a thought this morning - if I trim off the growing tips from coppice / Pollard poles, will the poles grow thicker rather than longer? I'm aiming to coppice / pollard mixed species (sweet chestnut, willow, ash, robinia, eucalyptus etc.) for firewood, fence posts etc, so aiming to get poles of 10cm diameter or so. If I let the poles grow to say 2m long (with the stools reasonably well spaced) then trim off the growing tips, will the poles thicken without getting too much longer? (Ive got some electricity lines on my land so can't let things grow too high in some areas...) Cheers.
-
Many thanks for typing all that out Gk, it does make sense and it certainly does help! Cheers.
-
Ahh, thanks BBB. That looks a good place to start.
-
Right, eventually got the correct carb kit (walbro wt-160B carb, not Zama) and replaced the various diaphragms. Metering diaphragm was shot, dissolving and floppy. Strimmer now runs! However, it's not set up quite right. It would cough but not start on choke, but I managed to start it without choke by opening the throttle a bit. Once it warmed up it would idle fairly well without throttle, but kept stalling. It also wouldn't rev fully, maybe 75% (a guess by sound, I don't have a tach) Once stalled it would restart with a bit of throttle. So I'm guessing the high and low screws needs adjusting. Tried to find default settings on the internet (2 turns out each?) buy found conflicting info. Does anyone know the correct default settings and a reliable tuning procedure? I assuming running it a bit rich isn't the end of the world, but running it too.lean could be... Many thanks.
-
Right, eventually got the correct carb kit (walbro wt-160B carb, not Zama) and replaced the various diaphragms. Metering diaphragm was shot, dissolving and floppy. Strimmer now runs! However, it's not set up quite right. It would cough but not start on choke, but I managed to start it without choke by opening the throttle a bit. Once it warmed up it would idle fairly well without throttle, but kept stalling. It also wouldn't rev fully, maybe 75% (a guess by sound, I don't have a tach) Once stalled it would restart with a bit of throttle. So I'm guessing the high and low screws needs adjusting. Tried to find default settings on the internet (2 turns out each?) buy found conflicting info. Does anyone know the correct default settings and a reliable tuning procedure? I assuming running it a bit rich isn't the end of the world, but running it too.lean could be... Many thanks.
-
You can get the ebook for free on project gutenberg...
-
-
If someone posts a wide image, the whole screen width increases to fit it in, meaning that all the buttons etc. (and half the text of replies) vanish off the side of my (big, high res) monitor. Not the end of the world, but a bit of a pain?
-
Ochsenkopf vs Gransfors vs Fiskars Splitting Axe/Maul?
sandspider replied to TimberCutterDartmoor's topic in General chat
I use an X27, and it's a nice axe. However, it was £50 odd when I bought it, and I'm not convinced it's 5x better than my old £10 toolstation maul which used weight rather than my force behind the axe to do the splitting. Having said that, I don't tend to split huge amounts of wood in a single session - the X27 is lighter so maybe better for larger volumes. -
Looks good. Love to see follow up pics in a year or two.
-
Oh, and the cheap carb linked about won't fit my strimmer, and they don't do one for an fs36 - so.I can't get one whether they're any good or not!
-
Hi all Had another go at it today. It'll run (a bit rough) on choke with half throttle, but if I take the choke off it dies. I took the fuel filter off altogether, and the fuel line appears to be crack free. Plug still damp, and if I take.it out and turn it over there's a fine spray of fuel from the hole. Also, if I.empty the fuel tank and pull it.over to clear.out the last drops of fuel, it starts.more easily and runs quicker and smoother. So.I assume the carb is the problem? Didn't check the tank breather, but there was no hiss when I took the cap off, so don't think it's that. I'd slightly rather fit a new carb than mess with a carb kit. But the only replacement carb I can find in the UK is 90 odd quid! At that price I'd just buy a florabest strimmer from lidl! That may be the best solution in the end anyway. Can anyone point me to an fs36 carb at a good price? Or the best place to buy a decent carb kit?.(I've seen a few on eBay, but don't know if they'd be any good) Thank.you.
-
Take a screen grab? That'll show what's on the phone screen with time and date...
-
+1, me too. It's not quiet (it screams a bit at full revs, plus the chain travelling is noisy) but it's quieter than my 2 stroke. My neighbours haven't complained, though they are a fairly tolerant bunch.
-
-
They're not sprouting yet, but I think the buds are swelling a bit.
-
Good growth for 3 years. Have you fertilised or mulched them or anything, or just left them to it? What varieties of willow and eucalyptus are they?
-
Thanks for the suggestions, all. If the posts aren't already cut, would cutting the tops to an angle not make things worse? Or would the water run off benefit outweigh "breaking the seal" of the pressure treatment? Steve, the posts are 8" diameter. But I'm really after something I've already got that I can put on tomorrow if I get 10 spare minutes. I do have some roofix roof-waterproofer, if that will stick to creosoted wood...
