Jump to content

Log in or register to remove this advert

Log Goblins


aspenarb
 Share

Recommended Posts

14 hours ago, openspaceman said:

I wonder what the calculations were that made them decide to go for the locks rather than a tunnel.

How would a tunnel work to raise the level of a boat to the next section ? If you tunneled level for the length of a canal section you would still have to lift the boat at the end of the section. Easier to have a few small rises instead of one great big one like the Falkirk Wheel. Anybody got any wood ?

Link to comment
Share on other sites

Log in or register to remove this advert

Erm?
Der tunnel goes through the hill, the locks go up one side and down tother, lad, to avoid tunneling through the hill like!

You’re right but the canal doesn’t go up and over a hill here ( I think) it drops from the high ground at Devises down to low ground towards Bristol, the canal could have gone through Marlborough which would have been a more sensible route but from what I remember on the information boards, the engineer who built it wanted to pass through devises.
  • Thanks 1
Link to comment
Share on other sites

7 hours ago, peatff said:

 Anybody got any wood ?

 

You missed out today all thats left is the few bits below :D

 

F6B1D959-0C3B-4FD3-8D0F-75A94DAE4060_zps

 

There is about 50 ton festering in the corner of the yard if you fancy rashering off a bit.

 

DADCC6B0-367C-4DF8-BEE9-6C4E411B2A29_zps

 

Strange you lot rattling on about canals, my lads are just fitting one of these fancy shithouse purification units with its own discharge pump. Canal boat discharges into it which is down a bank, gizmos inside do their thing and it pumps clean water uphill back into the canal.

 

I was a bit worried the bank would leech water into this hole but all was well.

 

C756AC98-28B9-418F-B4BC-40F7A188D4F6_zps

 

45CAE1BA-ADD4-4F32-978F-72E3B4AACC23_zps

 

Got talking to the owner and she was saying they have restricted boat movements between the locks in an attempt to conserve water.

 

E926C4A6-EBDB-4289-AFCC-0DD007508627_zps

 

 

 

 

Link to comment
Share on other sites

59 minutes ago, aspenarb said:

 

You missed out today all thats left is the few bits below :D

 

F6B1D959-0C3B-4FD3-8D0F-75A94DAE4060_zps

 

There is about 50 ton festering in the corner of the yard if you fancy rashering off a bit.

 

DADCC6B0-367C-4DF8-BEE9-6C4E411B2A29_zps

 

Strange you lot rattling on about canals, my lads are just fitting one of these fancy shithouse purification units with its own discharge pump. Canal boat discharges into it which is down a bank, gizmos inside do their thing and it pumps clean water uphill back into the canal.

 

I was a bit worried the bank would leech water into this hole but all was well.

 

C756AC98-28B9-418F-B4BC-40F7A188D4F6_zps

 

45CAE1BA-ADD4-4F32-978F-72E3B4AACC23_zps

 

Got talking to the owner and she was saying they have restricted boat movements between the locks in an attempt to conserve water.

 

E926C4A6-EBDB-4289-AFCC-0DD007508627_zps

 

 

 

 

That’s 85ggs porn right there!! ????

  • Like 1
Link to comment
Share on other sites

39 minutes ago, eggsarascal said:

Why is that tank being held down with the bucket b0D?

 

e6G,  spec was gadget was to be on a six inch concrete base, half filled with water and then backfilled with pea shingle. That hole was over 4.5 mts deep and shittank  position was critical so before the lads launched 20 ton of shingle around it I got them to rest the bucket of the machine on it to keep it steady.They have got a few more of these to do so will get some snaps.

 

b0D

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share


  •  

  • Featured Adverts

About

Arbtalk.co.uk is a hub for the arboriculture industry in the UK.  
If you're just starting out and you need business, equipment, tech or training support you're in the right place.  If you've done it, made it, got a van load of oily t-shirts and have decided to give something back by sharing your knowledge or wisdom,  then you're welcome too.
If you would like to contribute to making this industry more effective and safe then welcome.
Just like a living tree, it'll always be a work in progress.
Please have a look around, sign up, share and contribute the best you have.

See you inside.

The Arbtalk Team

Follow us

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.