Jump to content

Log in or register to remove this advert

Recommended Posts

Posted (edited)

This afternoon I milled 500 inch square ash stakes for a local wicker coffin manufacturer. LogBullet making life seriously easy. The DRO also proved useful for such a repetitive job. 

IMG_2720.jpeg

IMG_2737.jpeg

IMG_2735.jpeg

IMG_2738.jpeg

Edited by doobin
  • Like 12

Log in or register to remove this advert

Posted (edited)
9 hours ago, doobin said:

What concentration of tfr? Caustic? What brand?

CarPlan Trade Valet Hand Wash Car Concentrate Super TFR, 5 L

 

£15 for 5l

 

Have been mixing about 5 to 1 

Edited by Stihl123
  • Like 1
Posted
15 hours ago, doobin said:

This afternoon I milled 500 inch square ash stakes for a local wicker coffin manufacturer. LogBullet making life seriously easy. The DRO also proved useful for such a repetitive job. 

IMG_2720.jpeg

IMG_2737.jpeg

IMG_2735.jpeg

IMG_2738.jpeg

I might have missed it in a previous post but the DRO is something I’d like to put on my130, was that a woodlands kit or something you put together yourself. Any pics etc ??

thanks 

Posted
On 14/09/2023 at 22:31, doobin said:

This afternoon I milled 500 inch square ash stakes for a local wicker coffin manufacturer. LogBullet making life seriously easy. The DRO also proved useful for such a repetitive job. 

IMG_2720.jpeg

IMG_2737.jpeg

IMG_2735.jpeg

IMG_2738.jpeg


DRO?

Posted (edited)
On 20/09/2023 at 10:44, Johnsond said:

Digital read out for the head height 

Ah, yes. I go gaga after n iterations of “subtract 28 mm plus 3 mm from the number you first thought of”. After many silly mistakes when tired I learnt  to make a test cut then measure it by hand each time. This on my weekend-wannabe Christmas Cracker mill with nothing digital about it 

Edited by Mr. Ed
Posted
8 hours ago, Mr. Ed said:

Ah, yes. I go gaga after n iterations of “subtract 28 mm plus 3 mm from the number you first thought of”. After many silly mistakes when tired I learnt  to make a test cut then measure it by hand each time. This on my weekend-wannabe Christmas Cracker mill with nothing digital about it 

I'll post some pics in a bit, it's just a basic 600mm DRO slide mounted where the scale was. Sadly 600mm is an inch too short for the full travel of the 130max (so I placed a pair of G clamps to prevent the mill head going to full height) and I can't find anything larger in the UK. It's also started to give me ghost readings so I probably need to spend on something better but the largest DRO specialist in the UK was less than helpful hence just going for Chinese tat off Amazon.


A DRO makes it very easy but you still need to account for kerf. Much simple mental maths tho! If you don't have a DRO, by far the easest way is to place a set square set to the desired measurement on top of the cant and wind the mill up until the blade kisses it. Accounts for kerf too that way.

  • Like 2
Posted
4 hours ago, doobin said:

I'll post some pics in a bit, it's just a basic 600mm DRO slide mounted where the scale was. Sadly 600mm is an inch too short for the full travel of the 130max (so I placed a pair of G clamps to prevent the mill head going to full height) and I can't find anything larger in the UK. It's also started to give me ghost readings so I probably need to spend on something better but the largest DRO specialist in the UK was less than helpful hence just going for Chinese tat off Amazon.


A DRO makes it very easy but you still need to account for kerf. Much simple mental maths tho! If you don't have a DRO, by far the easest way is to place a set square set to the desired measurement on top of the cant and wind the mill up until the blade kisses it. Accounts for kerf too that way.

I’ve a few hardwood blocks made up in common cut sizes with a metal strip on the back to sit on top of the cant that I do pretty much the same thing with, a bit slow but gives good results. Have to work from the top down which is opposite to the Trakmet set works which is programmed with the last cut first but it’s no hassle in reality. 

  • Like 2
Posted

Got the 881 out for milling. First time in some months. It all went pleasantly smooth. 4” oak slabs for some posts in the future possibly. It was an old log but wood was pretty good. 
 

 

A6C56C55-4D60-4EB5-924E-9010E5C157DA.jpeg

E0D20374-5C32-4038-A537-BAC7644F72B8.jpeg

6A851AE0-EFD2-4695-BC5B-C398294A6380.jpeg

0A82AF22-0130-477A-ACBA-709BE06EC1BE.jpeg

  • Like 8

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  •  

About

Arbtalk.co.uk is a hub for the arboriculture industry in the UK.  
If you're just starting out and you need business, equipment, tech or training support you're in the right place.  If you've done it, made it, got a van load of oily t-shirts and have decided to give something back by sharing your knowledge or wisdom,  then you're welcome too.
If you would like to contribute to making this industry more effective and safe then welcome.
Just like a living tree, it'll always be a work in progress.
Please have a look around, sign up, share and contribute the best you have.

See you inside.

The Arbtalk Team

Follow us

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.