Bob_z_l

I cheap out. Old petrol and 2 mix in a pot with an old paint brush to apply. Wipe down after a few mins with paper towel then a blow down with the air line. Generally clears everything.

Hi Saul, How do you dispense out of the 55's. Is there some pump or tap you use to fill a combi? Cheers Bob

apparently no. From Wiki.... The two giant sequoia drive-through trees have both fallen: Wawona Tree fell in 1969 in Mariposa Grove, Yosemite National Park Pioneer Cabin Tree fell in 2017 in Calaveras Big Trees State Park[

That's well priced. Is it all metal construction and good with Milling chains? Yes. Cast....something. The motor is quiet and housed in aluminium. Yes, I would say so. Have a look....here is the manual. Ultra Mk4.pdf Available on their web.

I had a cheap grinder it's ok on everything except the ripping chains for milling. I recently bought a Portek and the ability to set the angles correctly has transformed my sharpening. The Granberg still goes into the woods with me but the bench s master. Portek Ultra ChainMaster MK4 chain sharpener – FR Jones & Son WWW.FRJONESANDSON.CO.UK

Similar from last night.... we've had 3 nests in the stables...2 clutches from each. Reckon this'll be mst of them getting set to go home.

I was looking at adding roller wheels to my panther mill. I was going t use cheap skateboard wheels on an extra long M8( I think) slotted in the rail. Might need to bush out the bolt... to be seen as I've not done it yet.

Cheers

Cheers @Stubby Makes me feel a great deal more at ease. Did you have to re-tune your saws a some others have said? p.s. I've just read more on the Stihl site. Their Moto Mix uses Ultra HP so I might go that route when pushed.

Sorry to hijack: Looking at Aspen @Rough Hewn but like to use a fully synth 2 stroke oil. Do you (or anyone) use the 4 stroke mixes and add your own oil? Or are you happy that the oil they use is good enough? I know milling is hard on machines and want to be super sure before I change. Quite happy to go on the search for super unleaded until they phase that out.

Hi @harveyWhite I used a 25mm square 16 gauge box steel length. Seems to be ok. An offcut from my scrap pile.

2 months. Ordered end of April delivered June/July from a reputable dealer. They get weekly updates on delivery times and should be able to keep you in line.

Sent you a private message

They shouldn't weigh that much if it's nice and dry. Can flip them over on the deck. Lad round here drives with them barely strapped. Often see them on the verge waiting for him to return. How he hasn't done anyone in is beyond me.

Wow!

You'll be a "time traveller" going into that one. What a whopper. I look forward to your vids of it. 👍 👍 👍 👍 👍 👍 👍 👍 👍 👍 👍

Are you sure you're not remembering the Rambo film where he joins up to fight the Ruskies? Rambo 3?

Were the bench legs an Ebay item too? I haven't seen anything like that n my searches. Mind if I pm you for a link?

Many thanks. For the £15-20 I can get one for I'm prepared to give it a go. If it doesn't work it'll go straight back on ebay and I'll move on. Thanks. Bob

Cheers Doug. This helps me greatly. Cheers Bob

We had a small tub for the old horse. Her feet used to crack up badly and you could dab a bit on to seal it and stop it getting infected. Bloody pricey to be buying loads only to bury it. Pine is full of natural creosote anyway isn't it?

Hi All, After damaging a couple of milling chains I realise a detector would be a handy purchase. However also noting this is a hobby and also being cheap until something proves it's value. I wondered If these Wand type detectors are any good? Has anyone tried them? Like TRYFUN Sensitive Hand-held Metal Detector. NEW (G1,) WWW.EBAY.CO.UK <p dir="ltr" style="margin-top:0; margin-bottom:0;">TRYFUN Sensitive Hand-held Metal Detector. NEW.</p> <br> <br> <p dir="ltr" style="margin-top:0; margin-bottom:0;">New in box... and ☆ Metal Detector DM3004A Handheld High Sensitivity Scanner Security Checker WWW.EBAY.CO.UK Model: DM3004A. Alarm: buzzer sound/LED alarm. LED indicator: working and low battery prompt. Long-lasting battery life: using smart power-saving technology, low power... Or do I really need to spend £100 or more? Recommendations??? Cheers Bob

Ditto. Had 3 pair sitting this year up from the usual 2 pair. After late start they are on to their second clutch of eggs by the look. Fingers crossed the weather doesn't put the mockers on it.

Only ever cut cookies with the Panther Chainsaw Mill. Easy peasy once you had first cut level. With mill, won't fixing/screwing it to a decent sized board and clamping the board work?

After reading all of this and reading again.... "The saw had been damaged when a large log fell on it and bent the bar, but a replacement bar seemed to be all that was needed." Are you sure the bar studs on the wonky saw haven't been damaged? if one was pulled up a bit the shoulder part might change the way the bar interacts with the spikes. Only wonky cuts I ever get are from bad chains. Hope you figure it out. following with interest.