Jump to content

Log in or register to remove this advert

Recommended Posts

Posted

My 560 has been very smokey recently, took the exaust of and cleaned ot to find where i think its coming from.

 

Hopefully there is a picture to go with this that shows the spot and you can see some oil there as well. Is there an easy fix for this?20190216_151848.jpeg

Log in or register to remove this advert

Posted (edited)

How bizarre. That looks like there's a leak from the crankcases, yet if that was the case you'd think the motor wouldn't be running too well. Could it be chain oil that's been spilt after an overfill, found its way to below the cylinder, and it's following the join of the crankcase join afterwards? What is the colour of your 2 stroke oil, or pre-mix fuel?

 

If it is an issue with a leak from the crankcase joint it could interfere with the fuel/air ratio and mix. 

Edited by Baldbloke
Posted (edited)

The gasket gets sucked in to the two haves making oil leak and get burnt on the exhaust can .  This has been sorted on later models by adding another crank case bolt . Yours may be the model with one less ?

Edited by Stubby
  • Like 2
Posted (edited)

Exactly as Stubby has said and I had exact same problem on an early 550 which I tightened up the crankcase ( 5 bolts later ones 6)retaining bolts but over did it on the one just behind where the leak is so be very careful ! That bolt is behind the flywheel. Really depends on the state of the gasket if it's ok most likely get away with tighten up maybe add a little thread lock before hand. 

My one was running fine only smokey !

Edited by outinthewood
Posted

Common fault on the older 560s, as previously mentioned, locate all the crankcase bolts on the flywheel side and crank them up as tight as possible but avoid stripping the thread or snapping the bolts.

Done a couple like this and seemed to work OK.

  • Like 2
Posted

I'm really glad this thread came up as my 560 has had a mysterious chain oil leak ever since I bought it! Anybody have a picture showing where the bolts are? Still learning all the names and locations of the myriad bits of chainsaws!

Posted (edited)

Remove the starter and flywheel and you will see most of them. Hidden one behind the ignition coil. Only two bolts holding it on. However when resetting the coil gap it should be .2mm. Most standard saws you just use a business card or similar but these need a closer gap. The crankcases are only magnesium it doesn’t take much to strip the threads. If the gasket is blown it is a strip down job or price up a short motor. Crank and cases complete. You would benefit from a short motor as you get the new type crank, crank bearings and updated cases that a 2018/19 saw has. Just a thought. 

Edited by Sveriges
  • Like 4
Posted

Cheers for that. This is an old one, probably within the first year they came out. I will give them a crank up and see if it fixes it.

Posted
Would that affect the running of the saw? It looks like it's from the bar oil tank. 
The saw runs fine, yes, its only bar oil. Just smokey as the oil gets on the exhaust when your cutting.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  •  

About

Arbtalk.co.uk is a hub for the arboriculture industry in the UK.  
If you're just starting out and you need business, equipment, tech or training support you're in the right place.  If you've done it, made it, got a van load of oily t-shirts and have decided to give something back by sharing your knowledge or wisdom,  then you're welcome too.
If you would like to contribute to making this industry more effective and safe then welcome.
Just like a living tree, it'll always be a work in progress.
Please have a look around, sign up, share and contribute the best you have.

See you inside.

The Arbtalk Team

Follow us

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.