Jump to content

Log in or register to remove this advert

Husky 550XP


axman
 Share

Recommended Posts

Log in or register to remove this advert

  • Replies 65
  • Created
  • Last Reply

Top Posters In This Topic

Just curious, how many years you ran stihl & husky saws WoodEd?

 

i used stihl for a good year befor i had even come across husky... the firm i work for only have stihl so i do actully use them.. luckly im one of the last there with an old ms361.. all my personal saw are husky. i did a 2 year stint of being self employed befor here...

Link to comment
Share on other sites

Did a bit of an experiment with mine today. Not had it out for a few weeks but it ran as good as usual.

 

Filled it up, pumped primer 4/5 times one there was some resistance. Choke, pulled couple of times til it fired, choke off, pulled a couple of times and it started.

 

Ran til it was dry, refuelled straight away, pumped primer 4/5 times once resistance felt, no choke or half throtttle, started first pull.

 

Ran part tank through then did something else for an hour or so. Set half throttle, started second pull.

 

Ran til empty and did the same as first time.

 

Had I been trying to start it lke an older saw and used choke after refuelling and cold start it would have flooded in no time.

Link to comment
Share on other sites

my husky 550xp starts not to bad but hesitates and cuts out a few times when cold, runs ok after heated up, is this an issue to be concerned about?

 

Do you mean as soon as it's started and you're trying to rev it out? Or do you mean after a few seconds but before it's settled down?

 

Quite a lot of 2 strokes are a bit farty for the first few seconds but settle down fairly quickly - most of the 357's I've used are notably like it and my old MX bikes were the same. Dunno what causes it though.

Link to comment
Share on other sites

Do you mean as soon as it's started and you're trying to rev it out? Or do you mean after a few seconds but before it's settled down?

 

Quite a lot of 2 strokes are a bit farty for the first few seconds but settle down fairly quickly - most of the 357's I've used are notably like it and my old MX bikes were the same. Dunno what causes it though.

 

yes mate a bit farty lol as soon as its started for the first few seconds. :laugh1:

Link to comment
Share on other sites

Did a bit of an experiment with mine today. Not had it out for a few weeks but it ran as good as usual.

 

Filled it up, pumped primer 4/5 times one there was some resistance. Choke, pulled couple of times til it fired, choke off, pulled a couple of times and it started.

 

Ran til it was dry, refuelled straight away, pumped primer 4/5 times once resistance felt, no choke or half throtttle, started first pull.

 

Ran part tank through then did something else for an hour or so. Set half throttle, started second pull.

 

Ran til empty and did the same as first time.

 

Had I been trying to start it lke an older saw and used choke after refuelling and cold start it would have flooded in no time.

 

The choke is replaced with the primer bulb for refuelling stats . thats the only difference .

Link to comment
Share on other sites

Having spent far too much tme reading the equipment forum, I finally bought the 550xp as a replacement for my MS260. I always liked the Stihl, a very faithful saw, but the Husqvarna is fantastic replacement, I am well pleased and have not encountered any problems yet! Thanks to the forum and Rouse's in Aylsham.

Link to comment
Share on other sites

Having spent far too much tme reading the equipment forum, I finally bought the 550xp as a replacement for my MS260. I always liked the Stihl, a very faithful saw, but the Husqvarna is fantastic replacement, I am well pleased and have not encountered any problems yet! Thanks to the forum and Rouse's in Aylsham.

 

Top blokes at Rouse's could i just say that if we all keep buying over the internet top places like that will be gone and we will all be in a muddle when ours saws need fixing in a hurry. We have already lost Robin Smith's i've been told. Rouse's have always given good discount and have always been there when the internet hasn't.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share


  •  

  • Featured Adverts

About

Arbtalk.co.uk is a hub for the arboriculture industry in the UK.  
If you're just starting out and you need business, equipment, tech or training support you're in the right place.  If you've done it, made it, got a van load of oily t-shirts and have decided to give something back by sharing your knowledge or wisdom,  then you're welcome too.
If you would like to contribute to making this industry more effective and safe then welcome.
Just like a living tree, it'll always be a work in progress.
Please have a look around, sign up, share and contribute the best you have.

See you inside.

The Arbtalk Team

Follow us

Articles

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.