Jump to content

Log in or register to remove this advert

t535li chain leaving rough cuts


Dilz
 Share

Recommended Posts

brand new t535/536li switched to 1/4" 10" pruning bar and chain (husky)  Chain leaves really ragged pruning cut and sometimes slips along the branch when starting the cut. tbh its rather crap. Any thoughts as to why?? 

 

Link to comment
Share on other sites

Log in or register to remove this advert

Try one of these and compare - if you put up a video on here showing one set up cutting.... pros and cons, then switch to the Panther Mini and chain - show this cutting - we'll refund half the price back to you [make sure you PM me after you have done so]. This offer only applies to OP unless you post a particularly good vid in which case it applies to you as well...

 

The 3/8 lo pro and 1/4 .050 will never cut as smoothly as the super thin 1/4 .043...

 

WWW.CHAINSAWBARS.CO.UK

 

image.thumb.png.abfd6a5df591421f6f2189111023d725.png

 

 

  • Like 2
Link to comment
Share on other sites

3 hours ago, billpierce said:

Is it .043 or .050 chain?

0.050 

going to switch to a .043 

though when i first tested the husky it was on 3/8  0.043 12" standard nose and it too was gash hence why we tried the switch to 1/4" and dime tip bars. 

Link to comment
Share on other sites

Try one of these and compare - if you put up a video on here showing one set up cutting.... pros and cons, then switch to the Panther Mini and chain - show this cutting - we'll refund half the price back to you [make sure you PM me after you have done so]. This offer only applies to OP unless you post a particularly good vid in which case it applies to you as well...
 
The 3/8 lo pro and 1/4 .050 will never cut as smoothly as the super thin 1/4 .043...
 
WWW.CHAINSAWBARS.CO.UK  
image.thumb.png.abfd6a5df591421f6f2189111023d725.png
 
 
Made this stunner of a vid rob!



Probably not the best ad for the panther bars, doesnt really show a massive speed improvement, but it is definately a much finer cut on the 1/4 043 compared to the 3/8 043
Link to comment
Share on other sites

37 minutes ago, billpierce said:

Made this stunner of a vid rob!
 

 


Probably not the best ad for the panther bars, doesnt really show a massive speed improvement, but it is definately a much finer cut on the 1/4 043 compared to the 3/8 043

 

 

 

 

 

That's not bad at all Bill and shows the control you get with the Panther Mini Bars - I sent you £15-00 thanks for posting.. image.png.6680defc8d3813b4424ff38803be6d90.png

 

 

  • Like 1
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share

  •  

  • Featured Adverts

About

Arbtalk.co.uk is a hub for the arboriculture industry in the UK.  
If you're just starting out and you need business, equipment, tech or training support you're in the right place.  If you've done it, made it, got a van load of oily t-shirts and have decided to give something back by sharing your knowledge or wisdom,  then you're welcome too.
If you would like to contribute to making this industry more effective and safe then welcome.
Just like a living tree, it'll always be a work in progress.
Please have a look around, sign up, share and contribute the best you have.

See you inside.

The Arbtalk Team

Follow us

Articles

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.