Jump to content

Log in or register to remove this advert

What's on your bench today?


spudulike

Recommended Posts

Log in or register to remove this advert

Just gave my 028super a good clean, sharpen and tune up. its going to a new home today :crying: love this saw but have just bought a 038super :thumbup:

 

Then gave the bench a well needed clean and tidy ready to strip and clean my 020t. How do you get the flywheel off the 020t? it doesn't use the standard screw puller?

Link to comment
Share on other sites

Sorry, I missed the "bottom" as I was on my Blackberry and a bit early in the morning, I thought it was the top one Dohh:lol:

 

I did see your post this morning but it was too early to reply I was still half asleep. Couldn't make heads nor tail of it. :confused1:

 

:thumbup:

Link to comment
Share on other sites

After months of plugging our macbook into the big tv due to an LCD invertor cable going wrong and no screen on mac, I ordered the new part around £16.50 delivered from arizona usa PBParts(highly recommended.) Fitted it today and now works brilliantly again.

 

I tried to get the part in the uk but to many apple rip off attitude merchants selling 2nd hand at higher price or doing the repair for £200!!!!!!

 

However I don't know if this post qualifys in this thread as I did it on kitchen worktop.

Link to comment
Share on other sites

After months of plugging our macbook into the big tv due to an LCD invertor cable going wrong and no screen on mac, I ordered the new part around £16.50 delivered from arizona usa PBParts(highly recommended.) Fitted it today and now works brilliantly again.

 

I tried to get the part in the uk but to many apple rip off attitude merchants selling 2nd hand at higher price or doing the repair for £200!!!!!!

 

However I don't know if this post qualifys in this thread as I did it on kitchen worktop.

 

A work bench is still a work bench mate. :thumbup:

 

Bit like my coffee table is a work bench. :biggrin:

Link to comment
Share on other sites

A 034 will be appearing on the bench at some point.

 

Runs ok from cold. Get about ten minutes in and it stalls, starts to loose power then won't rev up. Then dies and won't start again. Don't think it's fuel as you can smell it from exhaust after trying to start for ages. Let the diagnosis begin.

Link to comment
Share on other sites

Just gave my 028super a good clean, sharpen and tune up. its going to a new home today :crying: love this saw but have just bought a 038super :thumbup:

 

Then gave the bench a well needed clean and tidy ready to strip and clean my 020t. How do you get the flywheel off the 020t? it doesn't use the standard screw puller?

 

No Screw thread on the 020 or MS200T, there are a couple of methods - undo the central nut, first is to use a set of small pullers but this works better with the tank removed as it gives more access, the other way is to pop a large screw driver between the flywheel and crankcase, tap it in to place and whack the end of the crank with a hard plastic/rubber mallet - the end float on the crank will allow the flywheel to come off:thumbup:

Link to comment
Share on other sites

After months of plugging our macbook into the big tv due to an LCD invertor cable going wrong and no screen on mac, I ordered the new part around £16.50 delivered from arizona usa PBParts(highly recommended.) Fitted it today and now works brilliantly again.

 

I tried to get the part in the uk but to many apple rip off attitude merchants selling 2nd hand at higher price or doing the repair for £200!!!!!!

 

However I don't know if this post qualifys in this thread as I did it on kitchen worktop.

 

The kitchen worktop makes a fine bench as does the kitchen table - as long as er indoors is out and you clean all the crap off the surface and unless she comes home early:blushing::lol:

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  •  

  • Featured Adverts

About

Arbtalk.co.uk is a hub for the arboriculture industry in the UK.  
If you're just starting out and you need business, equipment, tech or training support you're in the right place.  If you've done it, made it, got a van load of oily t-shirts and have decided to give something back by sharing your knowledge or wisdom,  then you're welcome too.
If you would like to contribute to making this industry more effective and safe then welcome.
Just like a living tree, it'll always be a work in progress.
Please have a look around, sign up, share and contribute the best you have.

See you inside.

The Arbtalk Team

Follow us

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.