Jump to content

Log in or register to remove this advert

Some things moving


slack ma girdle
 Share

Recommended Posts

15 minutes ago, difflock said:

I have often pondered the need or rationale for 3 axles on a 3.5t trailer, surely 2 more widely spaced axles with suitably rated tyres would be just as stable, and with lighter unladen weight?

So does IW build them purely on demand based on ill-informed folk-story/hearsay  opinions? or because of some specific attribute the 3rd axle provides that I fail to recognise?

Or is it simply a case of being able to loose one tyre(or even 2 ) to neglect/underinflation/misuse/damage/punctures and still be able to drive on?

In theory harder to load badly. I’d say only on the longer trailers. I’ve a ten foot triaxle tipper and it’s almost impossible to load it so it tows well!

 

Three axles also allows you to have smaller tyres and wheels for the same weight capacity overall, and therefore a lower trailer. My Bateson 18’ tri axle does tow well. 

  • Like 1
Link to comment
Share on other sites

  • 2 months later...

Log in or register to remove this advert

  • 2 weeks later...
On 01/05/2023 at 17:36, slack ma girdle said:

Jacking over a backing leaning spruce.

I can tell that i have been spending too much time in my machinery,  there is a definite belly overhang.

Didn't know you had a thread or did videos... 

 

Can you send a link for that jack? It looks class. 
 

Am I right in saying you've cut your jack seat before you've even gobbed the tree out? Never seen it done like that before!

 

Sweet overhang 

  • Like 1
Link to comment
Share on other sites

Jack came from Chris Forestry

WWW.CHRISFORESTRY.CO.UK

The hydraulic wedge or prying arm allows the felling of big trees (from 45 cm diameter at chest height) without a lot of...

yep have always put the jack seat in first ,  it has always always made sense to support the tree first before putting in the mouth.

 

 

  • Like 3
Link to comment
Share on other sites

On 15/11/2023 at 23:01, slack ma girdle said:

Jack came from Chris Forestry

WWW.CHRISFORESTRY.CO.UK

The hydraulic wedge or prying arm allows the felling of big trees (from 45 cm diameter at chest height) without a lot of...

yep have always put the jack seat in first ,  it has always always made sense to support the tree first before putting in the mouth.

 

 

You've deep pockets. Haha. 
 

I just use a 20T off of eBay and does fine but how much heavier is this 30T? Would be good to have knowing you'll put just about anything over. Sometimes have to use 2 20 Tons to get some of our trees over. 

Link to comment
Share on other sites

56 minutes ago, JDon said:

You've deep pockets. Haha. 
 

I just use a 20T off of eBay and does fine but how much heavier is this 30T? Would be good to have knowing you'll put just about anything over. Sometimes have to use 2 20 Tons to get some of our trees over. 

What you are paying for is a certified jack designed specifically for tree felling. If it goes wrong you will still be covered by your insurance.

The only tree i haven't jacked over the wood of the tree failed not the jack.

 

Link to comment
Share on other sites

1 hour ago, slack ma girdle said:

What you are paying for is a certified jack designed specifically for tree felling. If it goes wrong you will still be covered by your insurance.

The only tree i haven't jacked over the wood of the tree failed not the jack.

 

 

Non tree specific jacks have been used for felling for ages and have finally been recognised by the powers that be.  Provided certain criteria are met the jack falls within the allowed scope - you can't modify the jack but it must have a removable top plate which can't deform and must have a collar attached.  

FISA Technical Note 001 _ Tree Jacking - August 2021 (1).pdf

  • Like 6
  • Thanks 1
Link to comment
Share on other sites

11 hours ago, Spruce Pirate said:

 

Non tree specific jacks have been used for felling for ages and have finally been recognised by the powers that be.  Provided certain criteria are met the jack falls within the allowed scope - you can't modify the jack but it must have a removable top plate which can't deform and must have a collar attached.  

FISA Technical Note 001 _ Tree Jacking - August 2021 (1).pdf 7.27 MB · 20 downloads

Thank for that,  thats a bit of bold forward thinking from FISA

Link to comment
Share on other sites

49 minutes ago, JDon said:

Insurance... I don't have any but I only really fell in big forests etc for one big contractor so I'd guess we are covered from them....

 

 

Maybe I'll push the boat out and buy one of those jacks in a few months. 

It's a shame you are the wrong end of the country, otherwise you could borrow it and see how it compares.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share


  •  

  • Featured Adverts

About

Arbtalk.co.uk is a hub for the arboriculture industry in the UK.  
If you're just starting out and you need business, equipment, tech or training support you're in the right place.  If you've done it, made it, got a van load of oily t-shirts and have decided to give something back by sharing your knowledge or wisdom,  then you're welcome too.
If you would like to contribute to making this industry more effective and safe then welcome.
Just like a living tree, it'll always be a work in progress.
Please have a look around, sign up, share and contribute the best you have.

See you inside.

The Arbtalk Team

Follow us

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.