aesmith

Funny you should ask, I was about to post. Ignition has stopped working on ours, no spark at all. I haven't yet rigged up a puller to get the flywheel off. So making the assumption that the "stop" wire connects to one end of the primary windings I these are the only tests I have done so far .. (1) Continuity - primary is a few Ohms, secondary a few 1000 Ohms. Those sound in the ball park but that is only my wildest guess (2) High impedance between the "stop" wire and the engine block (that's the wire that short to the engine to cut ignition off) (3) "some" voltage variation on the primary, if I connect a volt meter (digital) between stop wire and the engine I get some flickers on display when turning the engine over. Any suggestions would be appreciated. At the moment I don't really know how it's supposed to work, not have any idea where I might find replacement parts if any are needed. Thanks, Tony S

Exactly what happened. In fact I put the old fuel line back, the saw was in bits to replace the impulse line and I thought I'd do the fuel line while I was at it. Will pick up a genuine part next time I'm ordering from LS or passing the local chainsaw place.

That's interesting, regards it being Europe wide. I'm not sure why the UK would fall under anything "Europe wide" that doesn't come into effect until 2022, is that covered by some ongoing commitment? Also the legislation that was being planned would affect England on, or maybe England and Wales. Definitely not Scotland.

Alder used to be used for clogs, worked green.

By the way where does anyone find air dried offered at 25% MC? Or are we assuming that most suppliers actually don't do any better than that, even though most claim sub 20%. My local place (the £50 softwood) says they aim for 15-17% but are only promising sub 20%.

I wouldn't mind this lot, offered locally. But not worth £300.00, and there may be some issue getting the large section out. Firewood | in Aberdeenshire | Gumtree WWW.GUMTREE.COM Recently felled Beech tree, ideal for firewood. Buyer to collect - a few tonnes probably.

Back in the real world I don't need any sort of calculation to tell me that air dried softwood at £50/cube is miles better value than kiln dried hardwood at £140. Does anyone find prices in their area sufficiently different so that kiln dried wins out? Also in the real world we have the luxury of enough storage space that I can dry stuff for at least two summers before use so even if I do need to buy in now and again it doesn't need to be ready for use.

That's my mistake right there, my calculations were for M/C on dry basis, so when I said 25% I was assuming 1kg of wood plus 250g of water. Re-running on wet basis I expect my figures would pretty much match yours.

Interesting, I wonder if our method was different. I calculated loss from a kg of using .. Specific heat of water from 20 deg to 100 deg Plus Latent heat of evaporation @100 deg Plus specific heat of water vapour from 100 to 300 degrees

That's true and it's cracking stuff. We buy that now and again because our own supplies don't quite keep up with our use.

As you say you can't comment on value without some numbers. So let's kick off with what's available locally to me, which is air dried softwood at £50/cu.m or hardwood at £90 both claimed to be sub 20% m/c. The only local supplier of kiln dried is quoting £140 for hardwood, unspecified species, unspecified m/c. Let's just compare hardwood. Obviously if both are 20% m/c then kiln dried is 55% more expensive for the same end result. Even if the kiln dried is only 15%, and the air dried is actually 25% then kiln dried is still 53% more expensive.

Hi, asking here because I'm really after some layman's advice on Ash Dieback. We have a lot of Ash trees of every conceivable sort, from mature trees to regrowth from stumps to self seeded saplings. So I'd appreciate a few pointers .. (1) What is the best way for us to spot early signs? (2) If we find an affected tree, what's the best way to proceed? If it's small enough for me to handle should we immediately cut it down, and dispose of it (how?) (3) This is what triggered my post. I've been looking at a sapling that's showing no signs of the buds at it's tips opening. I know Ash is show to come into leaf but checking with binoculars I can't see any other example where the tips are not at the same stage as the rest of the tree. Is this an indication of trouble? It doesn't seem to be listed as a symptom in any information that I can find. Photo of one of the non-opening buds attached. The tree in (3) is actually unwanted, self seeded in a stupid place and I just haven't got around to removing it yet. I'm half inclined to go straight out and get rid of it. Thanks, Tony S

Just for fun I did some rough calculations and assumed starting temperature for fuel is 20 Deg C, vaporisation at 100 and flue temperature 300. And calculated the losses for each kg of water to be 0.83kWh. That's actually not very much in the scheme of things. Assuming you get 5kWh per kg of dry wood, the direct loss due to water is only around 3.3% for wood at 20% m/c, or just over 4% for 25. If that was the only affect of differing water content then it looks like kiln dried at 15% m/c would give something less than 1% more usable heat than air dried at 20%.

Surely 20% is 20% whether air dried or kiln dried? Or are you thinking that the kiln drying would have altered the properties of the wood as well as removing water? I expect that's possible. Some woodworkers prefer air dried, and I'll bet that kiln drying for firewood is a lot more brutal than for joinery timber.

That surprises me, do you know why that is? I can't see the requirement mentioned anywhere on a quick look. When we had the Rayburn the "hearth" was actually lower than the floor. It was a concrete floor with two layers of Marley tiles glued down, so the "hearth" was made by cutting off the tiles for an area in front of the Rayburn, and painting the bare concrete with some heatproof paint. Mind you there was not Building Warrant or anything when we did this, although the stove installer was pretty knowledgeable and methodical so I think he'd have let us know if that wasn't acceptable.