bolla

I think I will change the filters, but like Triggers broom pretty much everything including the hydraulic pump and rollers have been changed, well it is 27 years old

Hi my entec 30 dh chipper has an intermittent problem, will be working fine but very occasionally when its started again put to full revs the rollers wont turn. I go through various checks ie throttle on full, disconnect the hydraulic control from the red hand bar so can move the hydraulic control by the leaver by hand in case bar got bent. This is one of the first entec chippers it has stress control but no electric control or stop start reverse buttons its all done on the red bar push forward rollers stop pull bar back rollers reverse. Check a bit of wood has not jammed the rollers dont find anything wrong but start engine and rollers start again as if nothing is wrong It sounds to me that the chipper is on full revs as I know if revs fall rollers stop. but without a rev counter cant be 100%. air filter is clean I did clean the white mark that the stress control pick up senses, it was pretty dirty Am now wondering what this yellow wire is that is connected to the cooling system, could it be some sort of over heat rollers stop? chipper was ok when we finished today but would like to solve this issue Any ideas

Hi Im trying to remove the bottom roller on my entec DH 30 its same as Timberwolf 150 Ive removed the top roller , taken the bottom motor off ,undone the 2 allen bolts on the bearing side I put a ratchet strap around the roller and it moves freely but the spline drive on the roller is catching on the roller box so it wont come out. Ive had this roller out before and replaced the spline drive and it went back inn without having to remove the hopper so it should come out again. Any ideas Thanks

Hi you could try Bruce at Saunders seasonings, if he can use the trunk he maybe able to sort haulage Hardwood Timber London - Saunders Seasonings - Repurposed Timber WWW.SAUNDERS-SEASONINGS.CO.UK An award-winning low Carbon hardwood timber business selling London Plane, Oak, Ash, Beech, Elm and more -...

I was looking to replace my Timberwolf 150 hydraulic motors its an old machine and used the Char Lyn motors I sent one motor to Adan Hydraulics for them to match The reply We have received your Char-Lynn 101-1633 motor, and as requested we offer our AWMP 250S Adan Hydraulic Motor as a replacement, data sheet attached for your reference AWMP 250S Adan Hydraulic Motor priced at £221.16 each nett ex-works Carriage £13.30 nett Delivery 1-2 days from receipt of payment This was in Feb 2021 As there was little difference in the price I went with Parker motors

Hi am in the process of fitting new hydraulic infeed motors to my entec 30 dh chipper same as timberwolf 150 am also replacing the green plastic bearing bush, the old green bush was stuck in the roller the new one is a loose fit Is this correct ? Does the green bush need greasing and do the splines on the hydraulic motors to the rollers need greasing If so what grease should be used There are no grease nipples on this machine Thanks

hi what model entec is have you a photo and where abouts is the hydraulic oil comming from

Just in case you still need some one a bit more local Willow workshop stevenage do Lolar testing

Hi I had Stihl ms201 and ms261 stolen today from my truck tool box they forced the door The thieves were driving a white Vauxhal Combo van Reg DS20 GYP Its been reported to the police and am waiting on a crime referance When I check the van reg online it comes back as a Vauxhall combo can any one confirm this is a 20 plate vauxhall combo Also is there any quick way of finding out the registered keeper/ I realise it may be cloned but you never know Thanks

When using a frog walker system on 10mm rope for access what method is used if you need to come down before being able to tie in with your working rope system seen a few videos of going up but not how to get down on the same 10mm rope Thanks

My Entec 30 1998 model chipper same as Timberwolf 150 has very slow infeed rollers am guessing the hydraulic motors are worn out but just checking a few things before spending money Inside the hydraulic tank there is a filter that is screwed to the outlet port that feeds into the pump, you cant see the filter as its submerged in oil. looking online its called a suction filter and can cause problems if it becomes blocked {if clogged may restrict flow hence my slow rollers} I was thinking to change it but looking at the spares for this and similar machines there is no mention of such a filter Any one know about this filter and if its a changable part

Hi I have a Entec 30 DH 1997 Chipper with a Kubota 4 cylinder diesel its the same as a Timberwolf 150 Am trying to find out what RPM the engine should be running at while chipping and how I can check the RPM The rollers on the entec turn alot slower and they will jam much easier then my mates Timberwolf 150, his Timberwolf sounds to be working at a higher RPM I would like to check the RPMs on both chippers to compare Is there a reliable method of doing this Is there any recommendation of what is the ideal working RPM Thanks

Tipper motor and ram are off the old vehicle, the wiring including the 175amp fuse and switch gear were allready on the new vehicle. I never had a problem with the old set up but then I dont know what size fuse was in it. I will try a slightly larger fuse Thanks

I recently (christmas time)bought an ex demo mitsubishi canter tipper, I had the tipper body taken off and my old high sided body with old hydraulic ram and pump put on every thing has been working as it should untill today Today after tipping a heavy full load the body would not come down i traced this to a blown fuse on the lead that comes from the battery,the fuse is 175 Amp Little fuse MEGA This fuse the isolator switch and the up down switch are all oringal to the new vehicle ,is it possible the 175 amp fuse is good for say 1 ton tip if i try and tip 2 ton the fuse blows if so can i just put a bigger fuse if so how big ? or is it likely to be something else wrong

Chippers 21 years old. had a few issues with the hydraulics that I hope i have now fixed/ got the new fluid so want to change it