Ollie_M

just looking for some reccomendations of some good anti vibration gloves as i tend to get vibration shakes after running some of my older saws for a couple hours straight. cheers in advance

Don’t worry, just clicked how to use it

Take the carb off and go to bolt it up? Will crush the strato separator no?

so i bought the sealing plate above to pressure test my a 365 x torq as i read in multiple places this was the correct plate however unless something magical happens i dont understand how a simple circle metal plate with an 'inset' circle is supposed to fit with the strato divider? if anyone could put some light on this as to wether ive got the wrong part number or the wrong part in the right bag or what that would be great edit: so i just checked the workshop manual for the x torq range and it photographs and gives the part number for the plate ive got so now im even more confused? 😂

Most Stihl saws are still available as non m Tronic I think but rarely available stocked

can i just ask why not bar oil? its designed for the job at hand and therefore works well through pumps and looks after bars and chains.

following from difflock, on clarksons farm a company came out and used high pressure air to create cracks in the clay, they then filled the cracks with seaweed to hold them open - they did it in a puddle and you could see the bubbles coming up through the puddle showing where they aerated the clay. i would say worth looking into. also agree that that hole is the only permeable bit of your garden and is therefore acting as a sump for all the run off, a vigorous grass would help with this as it would hold the water and use it rather than letting it runoff however you wanted artificial so it is what it is

got a tree at the end of my garden - no clue what it is really but i have a feeling its dying as it was the first tree to loose its leaves around us last year by about a month, it was then the first tree to put leaves on this year - canopy started off well but it has thinned with time, not massively but it has. got some pics of a couple lower branches, that i trimmed the heartwood looks weird to me and all of them had pinholes in the center. just wondering what people think, it poses no danger and ill quite happily fell it if needed. thanks.

Check you got spark,and don’t spend money on a 180

185psi compression cold, she runs pretty strong IMG_2737.mov

Just checked ring gap - came in snug at .25mm so just under 10 thou 👌 looking forward to getting it back together - was the most powerful saw id ran when I got it and I was impressed then but not difficult after running a Stihl ms250 as a ‘big saw’ i bought the last 2 oem rings for ls engineers when I made an order, will keep them in the parts bin possibly for a pop up piston one day

Throttle open, normally make sure no choke but you don’t have one

cheers for that, had cylinder off today, base gasket was .45mm so will be nice a comfortable squish gap - got some hylomar blue of a mate which should be good as doesnt set so can take my time. i think max allowable ring gap is 1mm? didnt get the feeler gauges out but was very small gap when ring put it bore so should be ok, def was less than half a mm yeah that makes sense, baffle already drilled out but crocky's dual exit is very tempting when i removed the carb i found the rubber partition was folded and trapped under carb on left side (flywheel side), replacated by my finger. this may have been something to do with why this saw was being outran by a 038 super... as was very obvious that there was less fuel mixture entering through the left side of the cylinder/ tranfer port with it being almost clean compared to the golden brown colour of the right hand side. pictures of the removed fins from transfer cover below as i forgot to photograph the bore.

So just stripping the saw down ready to remove cylinder to do the transfer covers and am thinking I’ll do a base gasket delete and a ring replacement whilst I’m in there so just after a bit of advice as first time doing it. firstly, I’m looking at replacing the rings whilst I’m in there as can’t be bad idea to do them, comp is 150psi cold, piston is absolutely immaculate on exhaust side with machine marks still visible zero scratches whatsoever. No ‘special ‘ tools needed to replace the rings is there? Secondly I measured the squish currently at .95mm and I understand it wants to be just above .51mm - assuming gasket thickness from factory is consistent am I looking at needing no gasket just a sealant (recommendations please) or will I need some sort of gasket? lastly, saw has limited coil and I’ve tuned it so that it cleans up instantly when put on load and goes straight back to four stroking when unloading mid cut (as I understand to be correct) - however I’m about 1/16 if a turn off the upper adjustment limiter so thinking I’ll need to remove limiters as more fuel will be needed after mods? Is that correct? many thanks in advance for advice given

Yeah perfect, I like to use syringes for measuring out oil to mix aswell. the 5ml syringes seem the perfect amount to get a saw to fire off and run without flooding. syrings also quite handy for priming a bar - use it to run oil down the groove and into the nose sprocket