Jump to content

Log in or register to remove this advert

Recommended Posts

Posted
I've got two boxes of new old stock clutch drums if you put up a photo and sizes I might be able too help you out

 

Cheers Shavey, I'll do that, might be a couple of days before I get the chance though.

Log in or register to remove this advert

Posted

This just arrived today, a new old stock clutch/sprocket for a Danarm DD8F, 90 or so links of new old stock 7/16" Oregon chain and an assortment of tie straps/presets.

 

The chain has a bit of surface rust at one end and a few stiff links but it's in a diesel bath just now. I got it all off the guy on Gumtree. Looking forward to getting the chain/sprocket fitted to give the saw a try.

 

r-mac-albums-chainsaws-picture8047-danarm-dd8f-sprocket-7-16-chain.jpg

 

Thanks to all who offered suggestions/advice, much appreciated :thumbup1:

Posted (edited)

No I didn't bother in the end, was ready to place a bid but had other stuff to get that took priority. I wasn't convinced that the 110DDA actually came with a 7/16" chain/bar/sprocket, I suspected, possibly incorrectly that it would have been fitted with a .404, the later but very similar 110 was almost certainly .404 and would have had a smaller clutch/sprocket.

 

Just measured the clutch drum,

 

Inside Dia Clutch side - 90mm

Depth Clutch Drum - 20mm

Inner Flange Dia - 60mm

Spindle Bore Diameter Without Bearing/Bushing - 20mm

Bearing/Bushing Inner Dia - 14mm

 

The above measurements taken with a ruler rather than a vernier but close enough.

Edited by R Mac
Posted
No I didn't bother in the end, was ready to place a bid but had other stuff to get that took priority. I wasn't convinced that the 110DDA actually came with a 7/16" chain/bar/sprocket, I suspected, possibly incorrectly that it would have been fitted with a .404, the later but very similar 110 was almost certainly .404 and would have had a smaller clutch/sprocket.

 

Just measured the clutch drum,

 

Inside Dia Clutch side - 90mm

Depth Clutch Drum - 20mm

Inner Flange Dia - 60mm

Spindle Bore Diameter Without Bearing/Bushing - 20mm

Bearing/Bushing Inner Dia - 14mm

 

The above measurements taken with a ruler rather than a vernier but close enough.

Danarm 110 dda was my first chainsaw in 1970 and had 59ac .404 chain.

Posted
This clutch drum ive got here is a lot smaller so it must be for a smaller danarm it's about the only box that isn't marked

 

I have a smaller clutch drum for a Danarm, I'll measure it up but it looks like it's deeper than the one you have, pretty sure mine is for a 110/125.

Posted

Shavey, here's the measurements for the smaller Danarm clutch drum, think it's for a 110DDA, 110, 110 Automatic and 125 Automatic. The large one is the 7/16" one for the DD8F

 

r-mac-albums-chainsaws-picture8048-dsc-1369-copy.jpg

 

r-mac-albums-chainsaws-picture8049-dsc-1370-copy.jpg

 

r-mac-albums-chainsaws-picture8050-dsc-1372-copy.jpg

 

r-mac-albums-chainsaws-picture8051-dsc-1373-copy.jpg

 

r-mac-albums-chainsaws-picture8052-dsc-1374-copy.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  •  

About

Arbtalk.co.uk is a hub for the arboriculture industry in the UK.  
If you're just starting out and you need business, equipment, tech or training support you're in the right place.  If you've done it, made it, got a van load of oily t-shirts and have decided to give something back by sharing your knowledge or wisdom,  then you're welcome too.
If you would like to contribute to making this industry more effective and safe then welcome.
Just like a living tree, it'll always be a work in progress.
Please have a look around, sign up, share and contribute the best you have.

See you inside.

The Arbtalk Team

Follow us

Articles

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.