Jump to content

Log in or register to remove this advert

Milling oak


ashman
 Share

Recommended Posts

Drying time I find is around 8 weeks for 2" oak.

 

It takes a bit of time playing around kilning wood. Wastage isn't too bad but then the stuff I make I don't have to worry about the odd crack or 5 :biggrin:

 

Impressive stuff Rob! I haven't any issues getting 1.5 inch Oak dry (and thicker boards of other species) but the 2 inch stuff has required 11-12 weeks, not 8.

 

That said, I keep changing my mind about drying methods, and am going to try heat vent for the next one! :001_huh:

Link to comment
Share on other sites

  • 1 month later...

Log in or register to remove this advert

Hi, I have milled/had milled quite a lot of wide oak for canal boats - 2" for hull planks and 3" for bottoms now you can't get elm easily. To be honest, I've found you can get away with a lot. When through-and-through sawing the ones nearest the centre are most stable, and I do split clean up the centre as soon as the throat will reach, as I don't want a boxed heart, and I paint the end with cheap oil-based gloss to slow down differential drying. I then just stack in the shade with good thick sticks - say 1in for 3ft boards to let air through, cover the top not the sides and leave to dry.

 

I don't find a bit of windblown rain matters, and I find oak resistant enough to rot that any mould is surface only. However, sapwood is strictly sacrificial and I don't mill between end of April and start of Sept to avoid surface checking, which is controllable but too much effort!

 

HTH

 

Alec

Link to comment
Share on other sites

Hi Rob,

 

Your other question was about green vs. dead. I've usually used dead - standing or otherwise. They seem to dry out so slowly that a 3ft butt with the bark still on is still wringing wet after 10yrs lying! As such, it doesn't seem to make much difference, just pick the nicest looking one.

 

Alec

Link to comment
Share on other sites

Hi.

Yes i will certainly be using dead as thats all that i have available now, all the green stuff has been cleared for this year, but i have a few dead ones still standing and a few on the deck i have already dropped.

 

Rob.

Link to comment
Share on other sites

ditto everyone else...

 

slow I found is the key with oak.. the first 3" slabs I cut (55cm <--> ) warped more than the starship enterprise in the kiln - but then I'm not scared by a little joinery, so I didn't mind. I think it's a temperamental wood to dry well.

 

I also found the 2" oak boards taking about 8 weeks so far to 16%.

 

best results i've had so far are with yew, cherry, cedar...

 

I can wholly recommend milling and furniture making.

 

BTW, Rob, ive got some 8ft 120cm wide, 2" (and a few 3") chestnut slabs to kiln dry, how long? - butt had been sitting for a few years.

Link to comment
Share on other sites

I suppose in theory in a kiln they would still be the same as thinner slabs so 8 weeks ish for 2" but does depend on your kiln.

 

As said above it doesn't really seem to matter if the butts been down a few years as it'll still be wet!

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share

  •  

  • Featured Adverts

About

Arbtalk.co.uk is a hub for the arboriculture industry in the UK.  
If you're just starting out and you need business, equipment, tech or training support you're in the right place.  If you've done it, made it, got a van load of oily t-shirts and have decided to give something back by sharing your knowledge or wisdom,  then you're welcome too.
If you would like to contribute to making this industry more effective and safe then welcome.
Just like a living tree, it'll always be a work in progress.
Please have a look around, sign up, share and contribute the best you have.

See you inside.

The Arbtalk Team

Follow us

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.