Jump to content

Log in or register to remove this advert

346xp old style exhuast mod


Charlieh
 Share

Recommended Posts

ok a little picture thread, I bought this: (sorry about photo quality my camera is on the way out)

HPIM1169.jpg

 

anyway it was bought as a non runner, after a bit of messing about i decided the carb was the source of the problem,

 

poor photo but you can just make out the lump of blue pastic that was sitting under the metering needle spring, causing it to constantly flood the engine,

 

HPIM1164.jpg

 

Once that was solved it ran quite nicely, then I did a muffler mod on it, opening up the exhuast outlet area to about 75% of the exhuast port (i wanted to be a bit conservative as its my first attempt and a smaller saw, so i didnt see the need to go to 85%+)

 

 

 

After removing the exhuast I had to drill two holes and then filed and dremmel out the edges on both the exhuast and the mounting plate, the problem with the 346 exhuast is that it doesnt mount tight up to the mounting bracket so once you have drilled and filed the exhuast you then have to use needle nosed pliers to gently bend the outside of the hole you have created outwards so it touchs the mounting plate,

 

I also drilled a hole in the internal baffle as well, as i didnt go to the hastle of spliting the muffler apart, i drilled this hole off center to the exhuast port and new opening so it doesnt have a direct line through, my reasoning for this is that if you push the saw into something bushy like a conifer when limbing and a branch does push the screen in at least its not going to push it straight on/into the the piston

 

HPIM1166.jpg

 

I have then just used a small peice of isopon car body repair mesh as a spark arrestor mounted between the exhuast body and mounting plate, just to stop debris entering the exhuast

 

all told took just over an hour with the retune, which i did by ear need to get it on the tacho really now,

 

My first impressions are good, the saw pics up revs very fast, it seamingly cuts faster, the noise isnt as bad as i was expecting its certainly quiter than my 254xp (and less vibes and less thirsty). The fuel economy doesnt seem to have been adversly effected and im very happy, I used an older saw for this effort as its not a very tidy job but now i understand how to go about things i would be happier doing it on some of my newer saws, oh and i cleaned the huge amount of build up out of the exhust port which was probably about 1.5mm deep all the way around the port

 

so far the saw has cut about 2 trailer loads (7ftx4ftx2ft) of logs mounted to my portek log master, on one tank of fuel its great it will go into to timber the full legth of the bar (15") and doesnt drop the revs noticably at all,

 

my advice.....do it!

Link to comment
Share on other sites

Log in or register to remove this advert

Nice one charlieh, you got the bug now then:001_cool:

 

As a thought, if you do another, perhaps split the can open and remove the baffle completely, make the port on opposite side to the standard one then you wouldnt need the spark screen.

 

What you have done seems like a real good mod for a smaller saw, quick and cheap! Nice one!

Link to comment
Share on other sites

Nice job, I have split the can on my spare 361 exhaust and pulled the baffle out, splitting the can though, is a pain, I then blew some holes in it trying to weld the holes that the removal of the baffles left.

 

I have now left the exhaust with a friend who can actually weld.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share

  •  

  • Featured Adverts

About

Arbtalk.co.uk is a hub for the arboriculture industry in the UK.  
If you're just starting out and you need business, equipment, tech or training support you're in the right place.  If you've done it, made it, got a van load of oily t-shirts and have decided to give something back by sharing your knowledge or wisdom,  then you're welcome too.
If you would like to contribute to making this industry more effective and safe then welcome.
Just like a living tree, it'll always be a work in progress.
Please have a look around, sign up, share and contribute the best you have.

See you inside.

The Arbtalk Team

Follow us

Articles

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.