Jump to content

Log in or register to remove this advert

Recommended Posts

Log in or register to remove this advert

  • Replies 57
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Posted
I am hoping that the trees can be left up until June and I can then propagate like mad to preserve this particular genetic strain. I might end up with a house full of cuttings at this rate!

 

Alec

 

 

Don't have to wait until June Alec, you can take cutting now and put them in sharp sand they should start to make root in the spring, I know this because I did it with some elm cuttings last year from a 30" diameter tree which is hanging on in an isolated little wood. Took about 30 cuttings most of which made a nice root system this year. :thumbup1:

  • 3 weeks later...
Posted

Do the beetles wait for height or is it maturity?

 

Dredging my memory of lectures 20 years ago, I think the beetles find trees of a suitable height, where they feed in the leaf axils on twigs in the crown, infecting the phloem with the fungal spores picked up from the dead wood in which they hatched.

The infection then progresses up the branches and eventually into the trunk aided by the trees own nutrient transportation system, leaving dead branches and a 'stag-headed' look to the crown.

Debarking any felled infected timber will deprive beetles of egg-laying sites.

Posted

interesting thread on elm i have a few at top of my place and not big at present and look after them as such a nice tree to see. how do you take cuttings from them do you just cut some of the small branches off and put them in rooting compound then grow on and what is the best medium to plant in. i assume when 9ocm or above they then can be planted into the ground. and do you need permission from the forestry commission's to plant them as of ded and now ash die back.

Posted
interesting thread on elm i have a few at top of my place and not big at present and look after them as such a nice tree to see. how do you take cuttings from them do you just cut some of the small branches off and put them in rooting compound then grow on and what is the best medium to plant in. i assume when 9ocm or above they then can be planted into the ground. and do you need permission from the forestry commission's to plant them as of ded and now ash die back.

 

I clipped off some of the new twiggy growth ends it had made that year, then I clipped them back to a straight twig about 8-10 inch long. (Remember which end is the bottom or you will plant upside down :001_tongue:) With a sharp knife trim off the cutting just below a leaf node (small bump on the twig) and plant 3 around the outside of a 4 inch pot. Peat mixed 50/50 with coarse sand is a good medium. If you clip some willow into 2 inch pieces and put a few handfull into a container then just cover with water. If placed somewhere warm they will start to root and infuse the water with their natural rooting compound use this in the spring to water the cuttings. Keep them out of the direct sun as the leaves start to open, there wont be enough root as yet to support the leaves so nip off the lower ones leaving two or three at the top. Re-pot in the autumn plant out the following year, and away they go.

  • 2 weeks later...
  • 2 weeks later...
Posted

Smooth-leaved and English Elm are different species. We have a lot of Wych Elm (U. glabra) in our woodland, regenerating from stumps or as root suckers. It grows well until it reaches a decent size and then succumbs as the female Bark Beetle is attracted to it. The tree tends to die from the top down and can be maintained if you want to put the work in. Burns well enough too.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  •  

About

Arbtalk.co.uk is a hub for the arboriculture industry in the UK.  
If you're just starting out and you need business, equipment, tech or training support you're in the right place.  If you've done it, made it, got a van load of oily t-shirts and have decided to give something back by sharing your knowledge or wisdom,  then you're welcome too.
If you would like to contribute to making this industry more effective and safe then welcome.
Just like a living tree, it'll always be a work in progress.
Please have a look around, sign up, share and contribute the best you have.

See you inside.

The Arbtalk Team

Follow us

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.