CHC

I have been a big husky fan for a long time but had to get a replacement for a 372xp so was going to get a 572xp. But because husky cancelled the shops orders for some reason I tried a Stihl 462. I run a husky 562 and I don't use it now because and I hate to say it the Stihl 462 is a far better saw! It's alot lighter way more powerful and it is bloody rapid but so why pick a saw up that is heavier and with less power

A 550 xpg with 15inch Sugihara bar a 372xpg on a 24inch sugihara bar and a efco pole saw and a small Stihl chainsaw

Where in Suffolk? I don't want your postcode, just a rough idea.

thank you s g for the offer but had one saw some where else which was lucky

Hello everyone. My yard in the Suffolk area got broken in to today round about mid day. They cut the lock and took three saws a load of battery powered tools a pole saw and a plasma cutter so be vigilant the basterds are about

There's a company in Essex runs an Avant with a biggish Vector thumper on .
 

That may mask the problem but wont get to the reason ....there must be one !

What about shimming it so it sits further away from the drum my old 560 never had the problem either just my new 562

On warranty of course

I will have a look funaly enough I put the verniers on one yesterday and one bit it's slightly wider the the other. But the dealer put a new drum and sprocket on it so hopefully that will work

One side of the chain might be rubbing on the clutch. Had the same on my 562. It would cut straight for a bit then it would start to cut on the wonk so I would sharpen it then it would do the same again. The chain looks and feels sharp but if you look at the clutch side of the chain you will see a slight line where it's hitting the clutch. Had a friend who had four 560 and it's happened to them to. I would not of known it was that unless he did not say about it

What's an ordinary job?

Ten quid for a loaf?..   you must be out your mind..
 
I'm surprised you got 100 quid for a ton of wheat and only get 140 today mind..   still, it proves how much more efficient farming has become.. we should all tip our hat in that regard..
 
 
 
 
 
 

You thought about a efco the head then be tilted though 90*

Ok thank you for your help

Will it be one day?

Sugi hara but the ones with the resin inserts lighter then a Oregon bar don't need dressing as much. When it dose I have to use a angle grinder as files just bounce off them

Hello. Can you get the arb talk app on the Nokia 830 lumina have tried but so far no good.

Why not just use a fully threaded bolt with no shank?

The engine wont be using all its power.

 

 

 

If a tool needs 40hp at 540rpm that is all the tractor will supply. If the tool starts to bog down the tractor will up the power to try to keep it at 540rpm. If the tool bogs down too much the shear bolt will shear.

If the tractor is say 70hp and is running at 540rpm which would be about 1900-2000 rpm It will be putting out about 60hp roughly. So if a mower need 20hp the tractor will still put out 60hp other wise you would be able to put a 150hp tractor on a implement that only been 50hp to run it you can do it but if you push it to hard you will ruin the implement

Also might be worth taking out bolt and running it to see if it seized

It would not matter on size of bolt as if the sheer part of the pto yoke can take a m8 bolt you would not put a m6 in as it would potently damage the hole on the pto where you put the bolt through and if it stalls the tractor it would not damage the tractor as its no different to stalling it normally. if you look for the maker on the pto then do a search of the internet that might come up with the grade. Just to give you a idea though I run a big baler on a 200hp tractor and that has a m8 10.9 tensile strength bolt for the shear bolt but. A 8.8 bolt might also stretch rather then brake as the higher the tensile the more brittle they are. Sounds odd but but you can bend a 8.8 bolt but a 10.9 will brake before it bends as its a harder metal. But might be worth asking a ag dealer which Walterscheid or similar make if not sure

Dose any one find the pfanners ride up a bit to much in the crotch area when you have them with braces? Other then that I like them don't really think you will find a cooler pair of trousers

What's the wood?? I think about 2 ton

Grinder with flap wheel