Jump to content

Search the Community

Showing results for tags 'oiler'.



More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Tree Care Forum
    • General chat
    • Climbers talk
    • Tree health care
    • Trees and the Law
    • Homeowners Tree Advice Forum
    • Forestry and Woodland management
    • Firewood forum
    • Training & education
    • Business Management
    • Employment
    • Arb-Trucks
    • Large equipment
    • Maintenance help
    • Chainsaws
    • Stolen Equipment
    • Milling Forum
    • Chainsaw Carving Forum
    • Woodcraft Forum
    • International Arborist Forum
    • Landscaping
    • The Lounge
  • Sponsored Forums
    • Lister Wilder
    • Buxtons
    • Sorbus International Ltd
    • Treeshirtz
    • F.R.Jones & Son
    • Clark Forest
    • Predator
    • Spectrum Plant
    • Gustharts
    • Chainsawbars
    • Multione
    • Skyland Equipment
    • Forest and Arb
    • Treekit
    • Aspen Fuel
    • AJS Dolmar
    • Arborist Apps Support Forum
    • The Official Essential Arb Forum
    • Other offers
  • Arbtalk Technical Help Centre
    • Timberwolf
    • Greenmech
    • Forst Woodchippers
  • Associations & Organisations
    • AA
    • Arb Approved Contractor Forum
    • CAS
    • FCA
    • ISA
  • Past Events
    • Past Competitions
    • Christmas Charity Raffle 2007
    • Christmas Charity Raffle 2008
    • Arbtalk Christmas Raffle 2009
    • Arbtalk Christmas Charity Raffle 2010
    • Arbtalk Christmas Charity Raffle 2011
    • Arbtalk Christmas Charity Raffle 2012
    • Arbtalk Christmas Charity Raffle 2013
    • Arbtalk Christmas Charity Raffle 2014
    • Arbtalk Christmas Charity Raffle 2015
    • Arbtalk Christmas Charity Raffle 2016

Blogs

  • Member Blogs
  • Arboriculture
  • TD Tree and Land Services
  • HAIX Group
  • Steve Bullman
  • David Humphries
  • (Arboricultural-styled) 'Fact of the Day'
  • Tree Surgeon Insurance
  • Reasons Why Glazed Roofs Are Beneficial For Your Premises
  • Research
  • Can hair transplant be done to the places where hair never grew?
  • Barcham Trees
  • STIHL GB

Categories

  • Climbing Gear
  • Rigging Gear
  • Arborists PPE
  • Chainsaws
  • Hand Saws
  • Arborist Machinery
  • Firewood Machinery
  • Literature
  • Miscellaneous

Categories

  • Arborist Equipment
  • ArbTrucks/Vehicles
  • Arborist Machinery
  • Chainsaws
  • Agricultural/Forestry Machinery
  • Firewood Machinery
  • Miscellaneous
  • Timber Sales

Categories

  • Free Tip Sites
  • Pay to Tip Sites
  • Tip Sites That Pay You

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


About Me


Location:


Interests


Occupation


Post code


City

Found 2 results

  1. Can't solve this. Cany anyone add any light or similar issue? Rebuilt a 365 that had been crawled over by a tracked chipper. Included new bearing seals as split crank to replace clutch side. Ok. all back together with new rear handle to boot (non OEM but it seems reasonably rugged). Fired it up but chain is turning over with every pull. It ticks over and idle and Low adjust as they should hence discounted leak around new seals yet chain is turning no matter what. Looked a little deeper thought clutch was shot thus engaging with every pull, but springs not that weak. Pulled apart clutch side, I discover clutch appears to be binding with oiler (this after looking without sprocket on). The order things are reassembled according to diagrams are (thin washer) before oiler (so this sits virtually next to bearing seal) then oiler torx screwed down, then clutch directly on top (reverse thread). But even if i sit clutch only lightly tightened on it still binds with and turns oiler. This obviously then turns sprocket and hence chain. I prob should post pictures but there are so few parts involved, I cant seem to seat clutch without it tightening on to oiler and spinning it, there's plenty of play elsewhere and am used to tightening clutch down reasonably firmly and not catching on other models? even with a thin washer inserted in there its still going to pick the oiler up. Driving me mad, am wondering if crank has been bent (even only a microscopic amount) encouraging the clutch to bind? arghh Any ideas?
  2. Can anyone add any light on the following please? Rebuilt a 365 that had been crawled over by a tracked chipper. Included new bearing seals as split crank to replace clutch side. Ok. all back together with new rear handle to boot (non OEM but it seems reasonably rugged). Fired it up but chain is turning over with every pull. It ticks over and idle and Low adjust as they should hence discounted leak around new seals yet chain is turning no matter what. Looked a little deeper thought clutch was shot thus engaging with every pull, but springs not that weak. Pulled apart clutch side, I discover clutch appears to be binding with oiler worm gear (this after looking without sprocket on). The order things are reassembled according to diagrams are thin washer (so this sits virtually next to bearing seal) then oiler torx screwed, then worm gear with metal insert which houses above thin washer below. then clutch directly on top (reverse thread). But even if i sit clutch only lightly tightened on it still binds with and turns oiler worm gear. This obviously then turns sprocket and hence chain. I prob should post pictures but there are so few parts involved, I cant seem to seat clutch without it tightening on to oiler and spinning it, there's plenty of play elsewhere and am used to tightening clutch down reasonably firmly and not catching on other models? even with a thin washer inserted in there its still going to pick the oiler up. Driving me mad, am wondering if crank has been bent (even only a microscopic amount) encouraging the clutch to bind? The way it should work is sprocket should turn oiler worm gear, however the way it currently spins, clutch is driving worm gear> worm gear is the single 'arm' black plastic type, its in good condition. can anyone maybe redefine the order they have reassembled the above?

About

Arbtalk.co.uk is a hub for the arboriculture industry in the UK.  
If you're just starting out and you need business, equipment, tech or training support you're in the right place.  If you've done it, made it, got a van load of oily t-shirts and have decided to give something back by sharing your knowledge or wisdom,  then you're welcome too.
If you would like to contribute to making this industry more effective and safe then welcome.
Just like a living tree, it'll always be a work in progress.
Please have a look around, sign up, share and contribute the best you have.

See you inside.

The Arbtalk Team

Follow us

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.