Jump to content

Log in or register to remove this advert

GLynch

Member
  • Posts

    73
  • Joined

  • Last visited

Everything posted by GLynch

  1. GLynch

    Stihl ms200T

    THIS ADVERT HAS EXPIRED!

    • FOR SALE
    • USED

    Lovely saw sounds amazing much better than the newer top handle saws, this has had a brand new genuine Stihl cylinder and piston, also at the same time replaced the intake boot, oil seals, all the av mounts, fuel line and fitted a new bar and chain. It's not been used for any work since doing all of this. Saw can be seen running on collection Cash on collection please

    £350

    Bromsgrove - GB

  2. Just out of interest and to see if I've worked it out correct What would you be charging for a 7.5m 3 foot high picket fence? Just a straight 7.5 metre no gate or turns
  3. Ok thanks all, I thought pump would be more accurate just never noticed it before
  4. Bit of a random one but today I filled up my combi can with 5 litres of petrol then got back and put my 2 stroke mix in I then realised that on the fuel can it was actually measuring under 5 litres I went to 5 litres on the pump not the 5 litres mark on the fuel can, what does everyone else normally measure to? The fuel can or go by the figure on the pump?
  5. One I'm looking at is an 09 cs100 with 14hp vanguard engine, looks tidy for the age
  6. Anyone know what the cs100 is like with the vanguard 14hp engine as opposed to the 18hp? I'm just looking at buying one Also going to be selling my lipper cobra 6.5hp chipper soon Does alright tbf on smaller stuff and I just adjusted the blade gap makes a massive difference
  7. God knows what that site is
  8. Hi I'm looking for an 8x5 twin axle trailer with caged sides used as can't afford a new one, ideally wanted an ifor gd85 but struggling to find any and the ones I have seen are already sold Based in Birmingham west midlands area but can travel for the right trailer If you know anyone or anywhere that are selling them please message me Thanks
  9. Sorted! New pot and piston OEM fitted, saw runs lovely Thanks for everyone's help
  10. I wouldn't know where to start with that, might just try a non genuine cylinder and piston
  11. Looks like cylinder and piston are shot, the rings are moving free though
  12. I found that the intake boot was split so I've fitted a new one but still no improvement, I tried to do a compression test but I bought a cheapo compression tester but I don't think it works I e tried it on good working machine with the same result, also the spark plug is bone dry even after I get it running and keep the revs high, completely at a loss now
  13. Turning by the stub of the crank, I think they are in correct the smoother flatter side in first
  14. I have changed the seals on both sides and it felt very tight with the new ones fitted I couldn't turn the crank by hand
  15. I've checked the impulse line for splits and all looks good, I've stripped the tank off and checked everything I can think of even went round it checking that all screws were done up tightly, I haven't fully checked over the boot though so that may be worth another check over, I've ordered a compression tester so I'll give that a go aswell
  16. I've looked at piston but looks pretty clean to me, I'll try and take another look at some point, my struggle to check the compression as I don't have a tester Can't think of anything else it can be
  17. I have a 2004 ms200t that was bought as a non runner, it fires on choke then can usually get it running as long as I keep the throttle going, as soon as the revs drop it dies So far I've cleaned the carb and tried a working carb off another running 200t, also changed the plug and have good spark, changed fuel line, fitted new tank breather, new crank seals and still won't run, seems to have good compression I'm at a loss what to do next
  18. I've ordered the 9640 003 1190 seals so I'll give them a go first
  19. Thanks I did notice this when I had a look but wasn't sure if they fitted
  20. Hi all, I'm replacing the seals on my ms200t 2004 Can anyone tell me what the code is for new seals or if there is a better seal to fit other than OEM ones? Thanks
  21. Yeah I did see that but I'm not looking for a full time employed position as I have my own garden maintenance round through the growing season Thanks though
  22. Hi I'm looking for work as a groundie but hoping to move forward eventually and start climbing so I want to learn I have my cs 30/31, chipper and grinder tickets I'm 34 years old, based in bartley green and bromsgrove area, I've been doing groundwork for roughly 4 months on a subcontracting basis I'd be looking for anything really whether it be the occasional day or regular days each week, I just want to learn If you have anything feel free to drop me a message Thanks
  23. Hi all, I'm pretty new to tree work but I'm slowly trying to learn how to climb, I have all my climbing gear except for spikes, if anyone has any spikes they want to get rid of or sell then drop me a message and I may be interested. Not looking for anything special but I don't want to be spending £300 on a new pair when they will get hardly any use at the moment Cheers
  24. Hi all, I've been doing ground work since the beginning of September, I think I've learnt quite a bit in that time, I will be looking for work beginning of next year on a subcontracting basis whether it's regular work or the odd day when you have enough work for me I'm very keen to learn more and the aim is to eventually start climbing but for now I'd like to learn more on the ground. I have CS 30/31, chipper and grinder tickets Never miss a day if I say I'll work on a particular day then I will I'm 34 don't drink anymore and just want to learn and progress Based around bromsgrove/bartley green area west midlands If you think you have anything you can offer me please drop me a text 07958239500 or private message on here Thanks
  25. Anyone know if the new jansen chippers are any good? They do a 15hp loncin one for £2400 or a Kohler 14hp for £2800 Both look pretty good machines

About

Arbtalk.co.uk is a hub for the arboriculture industry in the UK.  
If you're just starting out and you need business, equipment, tech or training support you're in the right place.  If you've done it, made it, got a van load of oily t-shirts and have decided to give something back by sharing your knowledge or wisdom,  then you're welcome too.
If you would like to contribute to making this industry more effective and safe then welcome.
Just like a living tree, it'll always be a work in progress.
Please have a look around, sign up, share and contribute the best you have.

See you inside.

The Arbtalk Team

Follow us

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.