Jump to content

Log in or register to remove this advert

rem284

Member
  • Posts

    20
  • Joined

  • Last visited

Everything posted by rem284

  1. I checked them last night. Cheers
  2. No, I didnt check all the screws before use. I do think Ive been luck, might do the lottery this weekend
  3. adw. You were correct. I looked late last night and it was the one nearest the fuel primmer, the easiest one to access. The question is how did it get from there to the flywheel? So thanks to all, esp. adw
  4. That sounds like good news?
  5. If there is only one screw that holds the air injection nozzle on then its not that because its still there. I bought the saw second hand so I am secretly hoping the previous owner lost the screw and it was stuck somewhere until now. Even I can be lucky sometimes
  6. The screw has a flat end it's 4.85mm diameter and total length is 20.95mm. The head has a flange resembling a small washer. I checked exhaust and could not see anything missing there
  7. After cutting some ash with the 560 yesterday then re-starting after a fuel up there was an lot of rattling noise. So stopped and on inspection a allen headed black screw was found stuck to the magnet on the flywheel. I removed this and could not find where it had came from. I ran the saw since and it seems to be OK. Has anyone got an idea where it may have came from
  8. cut the bark on the sycamore and brush or spray roundup into it. The sycamore should die and then can be removed. Plant gap with required trees and maintain. I have done this before with success
  9. Depends on the site but if possible culling the deer would be the answer. We cull to try and get the damage levels less than 10%. On my beat all restocks are less than 10% and some 0%. I would plant a tree near the damaged one but a leave the damage one in the ground too and hope if the deer come back they will leave the new one and nibble the damaged one.
  10. beech outside is no good. Oak is the answer 3"X 3" will last about 50 years. Well creosoted Scots pine will last about 25 years.
  11. Guys, its sorted. A quick fix, the chain was up against the rim sprocket. Thanks to all the replies. As soon as someone mentioned it, the light came on in my head as I remembered I put the 18" bar on before heading out. Was worried for a while at the potential ££££'s. Cheers
  12. Just the starter pulley is moving freely, havnt tried owt else. Didnt see much shyte near the flywheel.
  13. about 3 weeks ago I used my 357 without any problems. I tried to start it this week but found it difficult to pull start. I removed the starting mechanism and it is ok and moving freely as it should. I put it back on and the problem remains. Any ideas on what to try next?
  14. I am not sure if it was a splinter or a insect sting but it was on my wrist. My whole hand is swollen and my forearm and hand feel bruised. I am now on antibiotics
  15. Does anyone have a bad reaction to splinters from cypress trees
  16. rem284

    Efco saws

    Thanks, Ive got a 199 to try out with a 48" bar but havnt had a chance yet. Ive looked on the Efco website and cant see this model. I hope to get a big saw to mill soon but dont know what to go for yet. I have the chance of a MS880 with a 48" bar for the same price as a one with a 30" bar
  17. rem284

    Efco saws

    Has any one got a large efco saw. What are your thoughts on them. How do they compare the the same size stihl or husky
  18. rem284

    husky 266

    Just started my old 266 up after about 5-6 years of being ignored for a 357. Started no problem and just cut some birch. I am thinking of using this for milling. whats the biggest bar I could put on this. its 3/8 at the moment, is there any advantage in going to .325, if so is it possible

About

Arbtalk.co.uk is a hub for the arboriculture industry in the UK.  
If you're just starting out and you need business, equipment, tech or training support you're in the right place.  If you've done it, made it, got a van load of oily t-shirts and have decided to give something back by sharing your knowledge or wisdom,  then you're welcome too.
If you would like to contribute to making this industry more effective and safe then welcome.
Just like a living tree, it'll always be a work in progress.
Please have a look around, sign up, share and contribute the best you have.

See you inside.

The Arbtalk Team

Follow us

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.