Dazonit
-
Posts
81 -
Joined
-
Last visited
Content Type
Profiles
Forums
Classifieds
Tip Site Directory
Blogs
Articles
News
Arborist Reviews
Arbtalk Knot Guide
Gallery
Store
Calendar
Freelancers directory
Everything posted by Dazonit
-
Well new fuel. carb cleaned .metering arm set level .adjuster screws 1 turn out and she is running sweet again thank you all for the advice much appreciated Cheers all daz
-
Will do mate cheers
-
Ill change the fuel ishould of done that strieght away dam. Tried fuel in pot no luck as I think its flooding so I'll change fuel and needle in carb .sthil not sure about fuel pipes as of the drawing noise not sure if it's drawing air
-
I'll give it a go tomorrow mate Should the metering lever be set level on this carb . Just watched a video on setting it Cheers spud
-
Set at 1 and a quarter at the moment but still not starting mate ?
-
not sure how to set the metering arm as I followed a video on YouTube to fit the kit the plug seems wet so I'll have a look at that first Cheers for the response
-
Hi all I'm after a bit of advice not used my 026 for a while got it out today it started but run rough tried to retune it and now it wot run and after trying to start it there is a noise like its sucking air. It seems to be getting furl Fitted a new carb kit last year and it started and run fine. Were do I start Cheers
-
Will do mate cheers
-
Well carb kit came today striped carb blew it through with the air line fitted card kit and it firerd up after 5 pulls cut a few logs it run sound and fired on first pull when turned off so seems to have done the trick . Thanks all for the advice all much appreciated
-
Carb kit orders bill I'll let you know how I get on
-
Cheers all carb kit and fuel line it is then hope it sorts it up post how I get on
-
I will get one orderd bill and see if that sorts it. It's just strange how once it started and been used it used to start day after day it's only when it's been unused for a while it plays up
-
Plug hole or remove air filter and inject fuel in that way only way I can get it to start when it's been unused for while Garry
-
Hi all my Stihl 026 has been unused for a few months and will not run it's been hard to start when not used since if owned it as I bought it second hand but abit of fuel in the plug hole and it fires and after doing this a few times it would run fine and start like any other saw even the next day . I tried this today and it will run until it burns the fuel put in the plug hole off then bogs down and cuts out any ideas please Cheers
-
Cheers mate But I see it states chainbreak none were this has a chain break ?
-
What cc is this saw ? I would guess 60cc i bet it was a top bit of kit when it first came out its deffinetly put together well i'm going to give it a clean and tune up at the week end as its ticking over too fast and runing on
-
The chain break even works I can't believe its still in production as its no oil painting to look at don't think I'll be keeping this one:biggrin:
-
Another PIC
-
I have just acquired this old saw it starts and runs and seems to be quit powerful for an old saw any info on it when it was made are they a collectors item I think the bar is 17" and it seems quit wide Trying to get pics up ?
-
What about fuel fit is it just a case of mixing it with petro andl still 2 stroke or would I have to retune ? And dose it effect the saw performance cheers
-
I think it will have to be aspen in the saws I don't use much or any saw I'm storing for a while to be on the safe side found my local stockist only 10 miles away . Is it okay to swap and change between normal 2stroke and aspen
-
As above how should a saw be stored while not in use for a while if fuel is left in the saw it could go bad and cause problems and if the fuel is drained pipes and thediagram could dry out and crack If a saw was run on a tank of aspen till it warmed up then toped up with aspen and stored would this solve the problem . I start any sawsi have not been using once a month which can be a bit of a pain but has worked so far or have I just been lucky ?
-
Well been running the saw a couple of weeks now and its done everything asked of it no probs . Iv noticed it dose like a drink/fuel but great saw I love it
-
I'm no expert but I would fit a new plug first and clean the air filter basic cheap and might do the trick
-
Bought this one for next to nothing it has a good 16" bar and starts 2nd pull it runs well and there is no scoring on the piston so if it is an early 80s saw it seems to have been well looked After I love a bargain
