steve collins

I have a months  FORESTRY work at canterbury starting september this year looking for someone who can get to site, work in all weathers and put in a days work consitently. Pay dependent on skill set.

Must have cs30/31 and first aid +F

Work is young coppice and oak felling 

Message on here please as signal is horrendous where i am at moment

Looking for an additional woodcutter to join a gang, must be reliable, able to get themselves to site, be organised and cut to spec.

Good rates paid, work is mostly on tonnage/m3 and mainly hardwood.

Must have Cs30/31    Cs32 would be an advantage and first aid at work.

Would be willing to take on an apprentice if only have Cs30/31.

send a message on here or phone Steve 07751057259

Cheers 

Looking for a response to the above to actual mpgs of people who own new or few year old 4x4's or vans as looking to upgrade soon .

Usual suspects, Hilux, Navara, Ranger, dmax, amorok,transit connect,merc citan, berlingo, transit custom or any others i have missed

Cheers

1 minute ago, bigtreedon said:

19 minutes ago, steve collins said:

yes three saws were up for grabs at a dealer and one went straight away, i guess the others have gone now. saw sounded nice although thought it would be lighter than a 576 but felt around the same

It is a far superior saw to a 576xp

Thats what i wanted to know

21 hours ago, Mark_Skyland said:

Im surprised if that is the case as I am fairly sure that there are non in the UK yet! Good news if they are though as have had a lot of interest and are still waiting on our order of them.

 

Have you seen them on the shelf yet?

 

 

 

 

yes three saws were up for grabs at a dealer and one went straight away, i guess the others have gone now. saw sounded nice although thought it would be lighter than a 576 but felt around the same

Dealers have some now  in uk 

Comedy gold thread again 

5 hours ago, MattyF said:

I’m not a HS freak either it’s just the folk visiting and inspecting our sites are.

Dont forget your own personal vehicle oil spill kit is the latest!!

on the husky technical's  i just take all the visor stuff off and just use a visor of a standard husky which clips into the ears defender mounts. think you have to replace the technical ears defenders of as well.

no  more flappy visor falling off

49 minutes ago, Sveriges said:

It’s not a common issue, those with bad seals have failed already the issue has been resolved for several years now 

seals

 its husqvarna using low quality seal parts causing the problem in the first place, dealer i spoke to today confirmed this. fuel is still an issue with saws left on idle too long and the carb wondering what it should be doing, also fuel filters clogging up and gauze in the carb becoming blocked due to bad pump fuel with high ethanol  levels

i think the problem was new top end on a high hours bottom end caused the second issue, do you think husqvarna are going to give out pretty much a brand new saw when the one purchased is worn out before the warranty has expired?? 

the saws are great just the build quality is still questionable 

I had same problems on a 560 ended up being a whole new pot piston carb luckily was covered under warranty few months later new crank seals then lasted a month then went in the bin!!

Ive split one of these husqvarna axes in half from just banging wedges(plastic) as the poll and axe are held together by some dubious fixing which is cleverly hidden by the rest of the handle. Great weight and size though

check the fitment of the pipe which oils the bar where it connects to the pump, found a split in it causing problems , ive had a few fail here over the years and also the brass filter in the the tank once was clogged up with fine gunk

Try Stuart ford fencing 01435 865170 based in heathfield sussex 

I used to work for them about 10 years ago

try, aworth surveys they travel/work all over uk

can you post a contact number

What boots are lasting the longest these days as seem to only get around 9 months out of a pair?

Cheers 

Looking for a spares or repairs 550xp if anyone has one for sale??

Cheers

looking for some prices for yew recently purchased or sold cubic ft 

Cheers

Steve

Ive got a brand new 372 xpw ported and polished from states but never used the disc cutter version

any other suggestions?, ive tried gladiators and didn't get on with the 3 pairs i had

What trousers is everyone using theses days when handcutting?

Ive been using sip innovation but found the zips are useless on them and havent been stitched properly from manufacturer.

Cheers