Jump to content

Log in or register to remove this advert

Cambium Savers


kram
 Share

Recommended Posts

Looking to get one, unsure what length or whether to have an adjustable prussik type, or just plain ring on each end.

 

I'd be fitting it as a retriveable anchor when I get to the top. I dont generally bother with a throw bag.

 

I remember being told that they work great over limbs but difficult to retrive if around a stem. I imagine I would use it mostly around the stem at the top.

 

I currently use a small sling and steel carabiner for the purpose but its not retrievable.

Link to comment
Share on other sites

Log in or register to remove this advert

Posted (edited)

It does appear to do everything except for being quite large and bulky to carry up on harness, and expensive for what is a peice of rope and three rings.

 

I have large and small steel rings and some spare rope already. I am thinking a tied clove hitch on the big ring in the middle will allow adjustment,  spliced eyes with small ring on each end. Or one end with a barrel stopper, I'm not sure if its useful to have one on each end.

 

A quick example without splicing, probably wants to be a lot shorter. Ignore the tail.

IMG_20241001_140113.thumb.jpg.5ce65aa6656ec41ac82b4b44f36eb57b.jpg

 

Edited by kram
Link to comment
Share on other sites

19 minutes ago, Steve Bullman said:

Theres a lot of knots in that setup, you're going to be getting that stuck A LOT.

 

Let's play devil's avocado here, decide we aren't buying anything, and instead streamline this device. What can we do?

Link to comment
Share on other sites

Ah, I made a mistake there, the clove hitch and stopper should be on the small ring with the large ring having a spliced eye, so that nothing can get stuck.

 

However after a quick test, a clove hitch wont work on a small ring as it wants to fold over, to become just two loops in the ring, although the stopper does stop it pulling out completely, its not going to be reliable.

 

Perhaps with a pair of bigger rings it could work, but I dont have them.

 

I was intending to avoid using a prussik loop but that might be the best solution.

Link to comment
Share on other sites

5 hours ago, kram said:

It does appear to do everything except for being quite large and bulky to carry up on harness, and expensive for what is a peice of rope and three rings.

 

I have large and small steel rings and some spare rope already. I am thinking a tied clove hitch on the big ring in the middle will allow adjustment,  spliced eyes with small ring on each end. Or one end with a barrel stopper, I'm not sure if its useful to have one on each end.

 

A quick example without splicing, probably wants to be a lot shorter. Ignore the tail.

IMG_20241001_140113.thumb.jpg.5ce65aa6656ec41ac82b4b44f36eb57b.jpg

 

Where did you get those rings from? Are you based in the UK? I've only found them on a Japanese website

 

If cost is an issue you can get a (non-adjustable) Stein cambium saver for £37 from Gustarts

Link to comment
Share on other sites

Posted (edited)

Rings from here, tho steel may be over the top. I got them for use as cinching anchors where I didnt want to trust alu but the small is a bit small, and big is too big for that use, so instead have some DMM 34mm alu ones for cinching.

HONEYBROS.COM

At Height 70kN forged Steel O Ring from Honey Brothers. The largest equipment specialist in the tree care industry.

 

Alu ones

HONEYBROS.COM

At Height 25kN Forged Aluminium O Ring from Honey Brothers. The largest equipment specialist in the tree care industry.

 

 

Yes seen the Stein ones, I think their shorter 90cm one will be about double the length I want. The longer it is, the lower your top anchor becomes on a small stem. I assume that any multiple wraps around the stem makes it non retrievable.

Edited by kram
  • Like 1
Link to comment
Share on other sites

The multisaver is a brilliant bit of kit, on small trees you set it long when dropping away from the anchor so your rope isn't rubbing on the stem and shorten it up when you go back up.

 Chogging a pole you lengthen it as the pole gets fatter, or round lumps, then you have a descendable drt anchor all the way down which is safer than just throwing climb line round. Put the rope through the third ring first, stops it hanging down and getting spiked.

 

So a well thought through, reliable, safe bit of kit. Works well, retrieves well, passes loler. Much better value in my opinion than eg ART ropeguide at over £200.

 

I haven't used my fixed length cambium saver once since buying it, definitely wouldn't waste money on one. Once you get used to a multisaver you can't go back, the fixed one is always too long or too short and hence a pain in the arse. As you say, wrapping ends your chance of retrieval, forget it.

 

I wouldn't hesitate to buy another.

 

Edit: forgot to say Stein make a version now as well.

Edited by Dan Maynard
  • Like 4
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share

  •  

  • Featured Adverts

About

Arbtalk.co.uk is a hub for the arboriculture industry in the UK.  
If you're just starting out and you need business, equipment, tech or training support you're in the right place.  If you've done it, made it, got a van load of oily t-shirts and have decided to give something back by sharing your knowledge or wisdom,  then you're welcome too.
If you would like to contribute to making this industry more effective and safe then welcome.
Just like a living tree, it'll always be a work in progress.
Please have a look around, sign up, share and contribute the best you have.

See you inside.

The Arbtalk Team

Follow us

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.