Jump to content

Log in or register to remove this advert

Double ended chainsaw milling


AHPP
 Share

Recommended Posts

I've got a 500i and a 661 that I want to buy a double ended bar for for milling. I'll also need to to either buy or make a mill. I want to get a big enough bar that I don't keep finding trees I can't do (without having to halve, skim and roll etc) but I don't want so big that it's either unreasonably unwieldy or it sags/flexes excessively.

 

 

What have people got and how are you finding them?

Do the proper mills keep the bar tensioned better than a DIY mill made from plywood and threaded rod?

At what length do you run into diminishing returns with bigger bars? 

What in your opinion is a nice compromise, all rounder size?

And I'd welcome any other input you think is relevant.

 

Thanks in advance.

Link to comment
Share on other sites

Log in or register to remove this advert

32 minutes ago, AHPP said:

I've got a 500i and a 661 that I want to buy a double ended bar for for milling. I'll also need to to either buy or make a mill. I want to get a big enough bar that I don't keep finding trees I can't do (without having to halve, skim and roll etc) but I don't want so big that it's either unreasonably unwieldy or it sags/flexes excessively.

 

 

What have people got and how are you finding them?

Do the proper mills keep the bar tensioned better than a DIY mill made from plywood and threaded rod?

At what length do you run into diminishing returns with bigger bars? 

What in your opinion is a nice compromise, all rounder size?

And I'd welcome any other input you think is relevant.

 

Thanks in advance.

Message rob D at chinsawbars or he is on here a fair bit

  • Like 1
Link to comment
Share on other sites

Plywood and threaded bar gives as good a cut as any pro mill if the bar and chain is right.
It is much slower to adjust to accurate increments quickly though.
Also they don’t last very long.
Chinese Alaskan copies are ok for mid range saws and bars, but only up to 48”.
If you regularly need to mill medium trees 18-42” diameter
I’d recommend the 60” panther mill and 54/56” GB bar.
It’s my go to mill for medium timber slabs.
If you want to make dimensional timber ie: beams, lintels, mantels and square edged planks a Logosol F2+ is ideal.
I’ve got all of them and others but those are the 2 we use weekly.
[emoji106]

Link to comment
Share on other sites

Plywood and threaded bar gives as good a cut as any pro mill if the bar and chain is right.
It is much slower to adjust to accurate increments quickly though.
Also they don’t last very long.
Chinese Alaskan copies are ok for mid range saws and bars, but only up to 48”.
If you regularly need to mill medium trees 18-42” diameter
I’d recommend the 60” panther mill and 54/56” GB bar.
It’s my go to mill for medium timber slabs.
If you want to make dimensional timber ie: beams, lintels, mantels and square edged planks a Logosol F2+ is ideal.
I’ve got all of them and others but those are the 2 we use weekly.
[emoji106]

Do you double end, Saul?
Link to comment
Share on other sites


Do you double end, Saul?

No, I don’t see the point.
The cutting speed is almost irrelevant.
It’s log and board handling that take up 95% of my time.
Whether a board takes 15 mins or ten.
It’ll take us 40 mins to move the log into position and set it up sometimes.
Unless you’re cutting over 2 metres diameter, one 880 is plenty,
And now with hyper skip chains, sharpening an 84” chain takes under 5 minutes.
[emoji106]
  • Like 2
Link to comment
Share on other sites

You’ll find slabs over 3’ wide and 10’ long are stupidly heavy.
A 4’ duromatic bar on an 880 gives a 100cm cut max.
Over that’s size a bigger mill is unbalanced on a log under 4’.
I can manage a 60” mill with a 56” bar gives me about 105-110cm on my own.
But I can’t even lift the 80” mill.
So it then becomes a two man job.
Best setup I’ve found is an 880 with a 60” panther.
But your 661 should cut up to 28-30” on a mill.
Maybe get a cheap eco mill off Rob.D and try that.
Takes a while to get your head around the theory of pith to pith and ladder set up with a first cut etc.
But it’s so much fun.
[emoji106][emoji106][emoji106]

  • Haha 1
Link to comment
Share on other sites

1 hour ago, Rough Hewn said:

You’ll find slabs over 3’ wide and 10’ long are stupidly heavy.
A 4’ duromatic bar on an 880 gives a 100cm cut max.
Over that’s size a bigger mill is unbalanced on a log under 4’.
I can manage a 60” mill with a 56” bar gives me about 105-110cm on my own.
But I can’t even lift the 80” mill.
So it then becomes a two man job.
Best setup I’ve found is an 880 with a 60” panther.
But your 661 should cut up to 28-30” on a mill.
Maybe get a cheap eco mill off Rob.D and try that.
Takes a while to get your head around the theory of pith to pith and ladder set up with a first cut etc.
But it’s so much fun.
emoji106.pngemoji106.pngemoji106.png

Get a bandsaw mill and your in dreamland ???

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share

  •  

  • Featured Adverts

About

Arbtalk.co.uk is a hub for the arboriculture industry in the UK.  
If you're just starting out and you need business, equipment, tech or training support you're in the right place.  If you've done it, made it, got a van load of oily t-shirts and have decided to give something back by sharing your knowledge or wisdom,  then you're welcome too.
If you would like to contribute to making this industry more effective and safe then welcome.
Just like a living tree, it'll always be a work in progress.
Please have a look around, sign up, share and contribute the best you have.

See you inside.

The Arbtalk Team

Follow us

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.