Jump to content

Log in or register to remove this advert

550XP Flywheel saga


GuyMo
 Share

Recommended Posts

So I bought a 550xp from a chap last month. Started but wouldn’t run (ruined piston).

Finally managed to get all the new parts etc and ran it. 
I absolutely loved it. Ran better than any of my other saws, and knocked spots of my 261 which is much newer and in better condition. 
I was using it to rip out a load of Leyland today when it gave a ‘pop’ and died!

I feared the worst and quickly got it onto the bench.

Absolutely no damage to pot/piston/crank etc.

 

However

 

I took off the starter cover, and the flywheel has sheared off from the crankshaft (not damaging it), and the part of the flywheel that fits in the groove on the crank (equivalent to the woodruff key on most) was in little bits.

 

Has anyone had anything similar happen? Any ideas how this could happen?

Freak occurance?

 

Ive ordered a new flywheel, are there anything that I need to be aware of when fitting it? It’s my first Husky that I’ve worked on, and it’s brilliant, far more intuitive and well designed than all of my other Stihl saws.

 

Link to comment
Share on other sites

Log in or register to remove this advert

The moulded in key can shear during starting if the flywheel isn't torqued down correctly, just make sure both the crankshaft and flywheel jointing surfaces are clean and grease free then I usually crank the locating nut down pretty hard. The only exception is if the flywheel central boss isn't solid and can crack under extreme pressure.

If you do a load of them, you know how hard to torque....I am sure ADW (Mr Torque Wrench) will give you the correct Nm figure!

  • Like 1
Link to comment
Share on other sites

But the crankshaft is clean?

Usually with a taper and key like this the key is more for location and the taper should take the drive, hence why people can get away with filing down a key to advance the timing and then locking flywheel onto the taper.

I would think it can't have been locked on properly, either contamination or a small burr or maybe locknut not to specified torque. Should be in contact over the whole taper area.

Link to comment
Share on other sites

1 minute ago, Dan Maynard said:

But the crankshaft is clean?

Usually with a taper and key like this the key is more for location and the taper should take the drive, hence why people can get away with filing down a key to advance the timing and then locking flywheel onto the taper.

I would think it can't have been locked on properly, either contamination or a small burr or maybe locknut not to specified torque. Should be in contact over the whole taper area.

Cheers! It’s probably some idiot not tightening the nut enough...

Link to comment
Share on other sites

5 minutes ago, spudulike said:

The moulded in key can shear during starting if the flywheel isn't torqued down correctly, just make sure both the crankshaft and flywheel jointing surfaces are clean and grease free then I usually crank the locating nut down pretty hard. The only exception is if the flywheel central boss isn't solid and can crack under extreme pressure.

If you do a load of them, you know how hard to torque....I am sure ADW (Mr Torque Wrench) will give you the correct Nm figure!

Thanks! Is there any reason why it would work to just fit a new flywheel, presuming the crank etc is ok?

Link to comment
Share on other sites

45 minutes ago, GuyMo said:

So I bought a 550xp from a chap last month. Started but wouldn’t run (ruined piston).

Finally managed to get all the new parts etc and ran it. 
I absolutely loved it. Ran better than any of my other saws, and knocked spots of my 261 which is much newer and in better condition. 
I was using it to rip out a load of Leyland today when it gave a ‘pop’ and died!

I feared the worst and quickly got it onto the bench.

Absolutely no damage to pot/piston/crank etc.

 

However

 

I took off the starter cover, and the flywheel has sheared off from the crankshaft (not damaging it), and the part of the flywheel that fits in the groove on the crank (equivalent to the woodruff key on most) was in little bits.

 

Has anyone had anything similar happen? Any ideas how this could happen?

Freak occurance?

 

Ive ordered a new flywheel, are there anything that I need to be aware of when fitting it? It’s my first Husky that I’ve worked on, and it’s brilliant, far more intuitive and well designed than all of my other Stihl saws.

 

Interesting. I'm in exactly the same boat...first Husky starts but won't run so time to open her up. Mind me asking if you used genuine bits or eBay? Thanks.?

Link to comment
Share on other sites

If the failure is just down to the fact the key on the flywheel has broken then as long as the keyway is clean, the crank taper and the flywheel hole is clean and grease free and it is well torqued down, there should be no reason  for it to fail again. Just check the flywheel to coil gap after torqueing it down as it may change a little.

I don't know why the original would have failed, sometimes, excessive use of a rattle gun on the clutch can loosen the flywheel or it may have been taken off at some time and not tightened sufficiently.

Link to comment
Share on other sites

3 minutes ago, Stihllymok said:

Interesting. I'm in exactly the same boat...first Husky starts but won't run so time to open her up. Mind me asking if you used genuine bits or eBay? Thanks.?

I cleaned up the original pot, bought a new piston (Meteor). I stupidly bought a different carb (recon) before finding out that it needed to be synced to the coil etc. I was unsure with how it would go (as I’m not particularly experienced) so I didn’t want to shell out for the original parts in case I ruined it. I’d heard excellent things about the Meteor pistons and so far it hasn’t disappointed! I’m hoping that once this issue is sorted, then I’ll be able to keep it running well, as the compression/acceleration etc is excellent!

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share


  •  

  • Featured Adverts

About

Arbtalk.co.uk is a hub for the arboriculture industry in the UK.  
If you're just starting out and you need business, equipment, tech or training support you're in the right place.  If you've done it, made it, got a van load of oily t-shirts and have decided to give something back by sharing your knowledge or wisdom,  then you're welcome too.
If you would like to contribute to making this industry more effective and safe then welcome.
Just like a living tree, it'll always be a work in progress.
Please have a look around, sign up, share and contribute the best you have.

See you inside.

The Arbtalk Team

Follow us

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.