Jump to content
Ds Tree services

Stihl 044 Top end question

Recommended Posts

I have sent a few emails I probably need to find someone that has some old stock.
Looking at the old cylinder it's gone through the crome plating on the exhaust side, I'd say the chance of cleaning it up would be slim.
 
The rest of the saw it in excellent condition and I love running it hopefully someone will carry the part and she'll be back to work.. 
 
Worth trying to hone it with some sand paper mate. Sometimes ally deposit can look alot like worn nikasil

Share this post


Link to post
Share on other sites

That is the impuse, who on earth said it would run without one? If the cylinder has no impulse then fit a nipple into the crankcase and take to the cab.

Share this post


Link to post
Share on other sites

Yup, ADWs advice is pretty much it, just need a brass pipe union, drill a suitable hole and push it in with a little epoxy or bearing lock to hold it in.

Running without an impulse - easy if you mount the fuel tank on the top of the saw!!!;)

Share this post


Link to post
Share on other sites
On 26/06/2019 at 12:21, wyk said:

If it's an early 90's, it's nearly guaranteed to be a 10mm saw.

Take a photo of the top of both cylinders. A serial # under about 1129 is an older, stronger 10mm version.

If possible, clean up the old cylinder. Early 044 and 046 cylinders were the best Stihl ever made.

Replace the catalytic converter if it's still in there with a new muffler, even if it is aftermarket. That cat has killed so many 10mm 044's :(

If it is an auto choke version, which it sounds like it is, then the lack of impulse passage makes sense. If it is not an auto choke carb, you need the standard cylinder set up. At least that's what I was told... I haven't seen an auto choke in person.

One thing to be mindful of, is that if you place a 12mm jug on a 10mm chassis you want to be sure the ring pins on the 10mm piston clears the port.

Serial no 1128

Share this post


Link to post
Share on other sites

By virtue of being 1128, it's a 10mm saw. Mine is also a 1128 vintage.

It also makes it a later 10mm, which were the stronger of the bunch.

What Stihl did, tho, was detune it with a cat and retard the timing a touch.

Advancing the timing 6* or so(.025" of the woodruff key), and removing the cat makes these saws run very strong.

If you remove the gasket for more compression, I would stick with .020 of the key just to be safe.

So, yes, that original cylinder is worth saving if you can.

  • Like 2

Share this post


Link to post
Share on other sites
11 hours ago, Ds Tree services said:

How will i know if it is a 10mm

Measure the gudgeon pin and little end bearing with a vernier when you take it apart. I don't know why Stihl did a 10mm and 12mm version of the same saw, mine is a 12mm with no cat and it cuts fine. Not much slows it down. I drilled a few holes in the baffle while I had it apart but it still has only one outlet.

Share this post


Link to post
Share on other sites

If anyone is looking for a good 044, feel free to contact me.

Share this post


Link to post
Share on other sites

That beast in your Avatar looks a bit like Boris Johnson to me.....some sort of Alpaca?

  • Haha 2

Share this post


Link to post
Share on other sites
28 minutes ago, spudulike said:

That beast in your Avatar looks a bit like Boris Johnson to me.....some sort of Alpaca?

No, he's a Tory MP isn't he ?

  • Haha 2

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Featured Adverts

About

Arbtalk.co.uk is a hub for the arboriculture industry in the UK.  
If you're just starting out and you need business, equipment, tech or training support you're in the right place.  If you've done it, made it, got a van load of oily t-shirts and have decided to give something back by sharing your knowledge or wisdom,  then you're welcome too.
If you would like to contribute to making this industry more effective and safe then welcome.
Just like a living tree, it'll always be a work in progress.
Please have a look around, sign up, share and contribute the best you have.

See you inside.

The Arbtalk Team

Follow us

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.