Jump to content

Log in or register to remove this advert

Tachometer mod


oldnwrinkly
 Share

Recommended Posts

I don't know if this is of any interest but .................

 

I have a cheap hand-held optical (non-contact) tachometer which I thought might be modified to work as a induction tacho to use for tuning saws.

In it's original state the unit has a low power laser which illuminates a piece of reflective tape that is applied to a shaft or flywheel etc. and a photo-diode which receives the reflected light pulses. My plan was to disable the photo-diode and replace it with a small induction coil which, when held close to the spark plug/HT lead (or the flywheel magnet) would pick up pulses and these would be de-coded by the circuitry to give a read out of RPM.

I tested the principle by resting a coil on the engine cover and measuring the output on a DMM set to read frequency. I also compared the accuracy of the readings by fixing a magnet to the chuck on my minilathe, which has a tacho, and after converting the frequency reading to RPM (x60) the readings were identical.

So, today I knocked up a rough and ready, very simple circuit, soldered it into the tachometer and tested it against the lathe taco. It matched the readings exactly up to 1,000 RPM - I didn't take it any higher as although I had added a few bands of tape over the magnet, the thought of what could happen should the magnet let go is scary.

I am fairly confident that it will be just as linear at higher revs as although the unit is a cheap one the chipset looks reasonable - the microcontroller is an 8051 type (Atmel AT89S52). As soon as I have made a proper job of adding the bits and pieces into the case I will try to test it against a commercially available 'saw' tacho.

 

If anyone is interested the add-on bits are - a small, fine wire, coil wound on a thin ferrite core, a 'snubber' diode wired directly across the coil and a series diode, for polarity purposes, on one end of the coil. The positive lead of the photodiode was snipped and the cathode ( ->l----) side of the series diode connected to the circuit board end of it. A short length of wire was added to the other side of the coil and this was soldered to the negative lead of the photo diode. The polarity of the photo-diode leads are marked on the circuit board.

The laser will still light up but this will not matter.

I intend to add a switch so the unit can be used in either the optical or induction mode.

I bought the tachometer on evilbay for very little money - it is identical to this one < LCD Digital Laser Photo Tachometer Non Contact RPM Tach Last Max Min Value Top | eBay >

 

 

Dave.

Link to comment
Share on other sites

Log in or register to remove this advert

I haven't read all the post but I had an old tacho at work which used a piece of reflective sticky tape - only problem, the tape flew off when the shaft got up to speed:thumbdown:

 

buy a tiny tach - brill:thumbup:

Link to comment
Share on other sites

  • 8 months later...

Sorry to drag up an old thread but i have been thinking along similar lines. I have pretty much the same cheapo optical tach and think it would make a nice little project to turn it into a inductive tach.

what gauge wire and how many turns did you use? if i understand it right, the number of turns will alter the induced voltage across it?

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share

  •  

  • Featured Adverts

About

Arbtalk.co.uk is a hub for the arboriculture industry in the UK.  
If you're just starting out and you need business, equipment, tech or training support you're in the right place.  If you've done it, made it, got a van load of oily t-shirts and have decided to give something back by sharing your knowledge or wisdom,  then you're welcome too.
If you would like to contribute to making this industry more effective and safe then welcome.
Just like a living tree, it'll always be a work in progress.
Please have a look around, sign up, share and contribute the best you have.

See you inside.

The Arbtalk Team

Follow us

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.